side table makeover!

Remember my before pic- this side table in need of TLC. I almost tossed'em or yard saled the pair- since they were only 60 bucks brand spankin new and aren't even made of real wood! BUT the size and shape could work, and I needed the little drawers for living room storage- so I stayed with it.

I painted the tables black- using a DIY chalk paint formula. I used chalk paint so I could skip the prime step and skip right to the paint. And for the record chalk paint does have great adhesion to MDF, I was very pleased with it.

I took off the top of the table, to be replaced with some real wood!

To create a metallic look I started off using Jamie's {Freckled Laundry} tutorial-it's about the best tutorial I've ever seen. Jamie is so super duper talented.

I happen to have the right paint on hand to follow through her directions. I probably shouldn't have taken a pic with the freezer paper- it's really just a trick I use to keep the paint from soaking into the paper plate. So you can disregard it when/if you buy supplies.

Following the tutorial, you use a rag to blend three shades of silver, creating a slightly varied finish in color. Buuuut, I followed all 14 steps and wasn't that happy with my version-{*super sad face.} Though this was at no fault of the tute. More like I'm still working on my glazing skills. So I backtracked to step 5.

I wanted a more reflective surface. So I used my old friend, Rub n Buff, to apply another level of sheen. I also used this to create imperfections in the finish and create depth. Look at how the furniture reflects light. I took this pic n an overcast day with the curtains closed, and still you can see the shine!

Here's a few close up shots so you can see the finish. I applied the Rub n Buff with a toothbrush, like I explain here. I used it in spots, making it thicker and thinner in areas to help recreate the look of metal.

I used cheap-ish preassembled pine wood and had it cut it to size. I decided to cut them the same size as the base, trying to modernize the traditional tables a bit. The wood cost me 20 bucks and would have been cheaper if I had decided to make my own with planks- probably costing $12-13. This time easy won, though!

Then I used a homemade stain made from vinegar and steel wool to age and stain the wood. {I describe it in depth at the bottom of this post.} The wood is warm with gray tones in it. It is a little more yellow than I'd like- but that's due to the polyurethane, not the stain.

I can say I'm at peace with how the tables turned out. For about 25 bucks I don't have to stare at that red-toned "wood" ever again! Not bad for a 60 dollar Target table, huh?

theory I wish I could be the coffee table type- sporting an old railway cart as the centerpiece to my room. But it isn't practicle for the way we live, especially while we're living in a small space.

So- we're ottoman fans cause we like to lounge on our couch and you really need an ottoman for that.

When I sold our couches last June-ish I kept the ottoman. Then it sat in the middle of our room in all it's corduroy and tapestry glory. I am super excited to have something we use every day look like it belongs in my room!

I kept it because it was the right height for the new couch, it was fairly expensive, and I had plans for this baby! The ottoman I was crushing on was from Ballard Designs- with a nubby oatmeal fabric it would fun me $495- which, I think, is how much we paid for our ottoman in the first place. All the more reason to reuse mine.

It was pretty easy for me to get from this before pic to my after. I put this project off- forever- because of the sewing issue. See, I can't, and I knew I would need to sew the bottom portion to make this look like something I would buy- not something I made.

I used a drop cloth to make this after happen AND with minimal sewing- if you can sew a button, you can do this project!!

1] To start- flip your ottoman over and use some pliers to pull out the staples, so you can take the fabric off. Don't worry about keeping the original fabric in tact- this can easily be done without it as a template.

2] Once you ottoman is naked- you'll need this stuff to get'er done. If your foam and batting are in good shape, then you can reuse them. I reused mine. I had everything on hand except the button kits, peg board, and upholstery needles- so it was a cheap makeover.

3] Purchase a drop cloth that is long enough to be wrapped around the entire base of the ottoman. This is a crappy pic- but if you follow the arrow, I wrapped the fabric around the base so it would meet up in one place. Also- make sure the cloth is wrapped inside out!

4] Pin it where the fabric meets up. You should try to pin it in as straight a line as possible. When I got to this point I decided to make it a skirted ottoman, instead of following the inspiration pic 100%. So it is more like a combo of Ballard's slipcovered ottoman and their tufted one.

If you're making one like mine, then make sure you use the finished edge of the drop cloth as the edge that touches the floor- less sewing, you know.

I somewhat followed this tutorial to do the tufting- it is very comprehensive, with lots of photos- so pop over if you need things clarified.

5] Cut the pegboard the same size as cushion. Use the grid to plan out the button spacing.

6] Wrap your foam in batting, then cut holes in the foam where the buttons/tufting will go. I kinda skipped this cutting step- but you should totally do it! ;-)

7] Make your buttons using the directions that come with your kit.

8] Thread your needle with the twine and create the tufting. Make sure the buttons are seated down as far as they will go.

9] Don't forget to manipulate with the fabric to create pretty tufts before you secure the button in place with your staple gun. Here's mine, pre-ironing.

Now- for my Achilles heel- sewing. I know I CAN sew, if I could just LEARN how to!! lol

I spent 2 days playing around with this beast that was given to me 2 weeks ago.

All I ever got was a tangled mess- no sewing. The thread would just bunch in a knot. Is the machine broken? Maybe it's the user!! Hmmph!

10] Remember how I said if you can sew a button, then you can make this ottoman? Yeah, so I hand sewed it. You'd think it would take a long time- but not compared to the 2 days I spent on the sewing machine! I made sure my pins were straight, marked a straight line with a pen and that kept my stitched straight.

On the left is my hand sewed seam- then on the right, my drop cloth came with a big fat seam down the middle of it. So I lined that one up the opposite side and opposite corner as my hand sewn one.

11] Make sure you iron the tufting- and well, the whole drop cloth for that matter. But ironing the tufting will just help it stay the way you want it to- and it will look pretty!

If you didn't want a skirted ottoman you could easily wrap the fabric {like a present} under the frame and staple it in place. Then it would look more like the original inspiration. I may do that at some point? Who knows? Z had a strong opinion that is looks better skirted- so this will work.

This makeover cost me maybe 20 bucks. The drop cloth cost me $11 {I bought a 6x9} and I used coupons when I bought all the supplies- this really kept costs down.

Even though I had an ottoman- you could easily do this with a thrifted one or something you found on Craigslist. Funky outta date ottomans are always floating around out there!