I am trying to replace a light ballast. They both have red wires coming out of thr right.
-
3po3 on Jan 14, 2012Can you take a picture of this setup? And I'm not absolutely certain what your question is.Helpful Reply
-
-
Woodbridge Environmental Tiptophouse.com on Jan 15, 2012The wiring of this type of lamp must match the wiring diagram that is on the face of the new ballast. If it does not have one which most of them do, then you need to check with the manufacture of this product for the wiring diagram for this replacement unit. You must be sure that this is the correct ballast for the lamp size and type your using. Some have auto starts, some require a starter. What ever you purchased must match exactly what you currently have or you risk an explosion of the new ballast being put in. Here is a link that you can perhaps refer to. About mid way is wiring diagram. http://donklipstein.com/f-lamp.htmlHelpful Reply
-
-
LandlightS on Jan 15, 2012You have an electronic ballast that is replacing the old magnetic ballas (which are hard to find today thanks to Gov't regulations). It will work fine but you have to rewire the fixture to match the wiring diagram on the ballasts. Also check to lamp description: is this ballast for a T12 lamp or a T8 lamp (or both). If you decide not to attempt to rewire the fixture, either have an electrician install the ballast or return it and purchase a new fixture with an electronic ballast for just a few dollars more.Helpful Reply
-
-
LandlightS on Jan 15, 2012PS: hate to say it but the link from Woodbridge is outdated. It states that a 4 light fixture will have two ballasts and if you go to HD, Lowes or any Ace Hardware you will find a 4 lamp electronic ballasts that replaces the 2 old magnetic ballasts.Helpful Reply
-
-
Woodbridge Environmental Tiptophouse.com on Jan 15, 2012Thanks Landlights, I will update my library accordingly. I would think however regardless of type etc. Does not the ballast have the wiring diagram on the face of it? That should answer his question I would think?Helpful Reply
-
-
LandlightS on Jan 15, 2012Yes, th ballast does have a wiring diagram, however they are always not that easy for a DIYer to understand. With the electronic ballast, the neutral no longer goes to the lamp holder, but to the ballast, and that is where it get confusing. If he were replacing a " rapid start" ballast, he would find the neutral connected to the ballasts.Helpful Reply
-
-
Don H on Jan 15, 2012Thanks Woodbridge and Landlights-Diagram helped , and not needing a neutral wire to the lamp holder.Helpful Reply
-
Related Discussions
Would you rather wash and fold laundry or clean the dishes?
Given the choice, would you prefer washing the dishes or doing laundry? Share your preferences and insights!
What can I do about wood smoke coming into my house?
I need help. My back door neighbor heats with a wood stove all winter. They are downhill from me. Almost all their smoke makes its way into my house, causing headache... See more
How to tighten a lamp that is looose?
How to tighten lamp that is loose?
How can I inexpensively add some "wow" to my very brown/tan house?
My house is 100 years old and rock solid but it is bland. It needs someone's creative suggestions!
1950 Doors
I hate these doors. I'm not a carpenter. Was wondering if these would look better painted? What can I do with these door knobs? The plating or whatever is coming off.... See more
Does anyone have any good suggestions on how to keep squirrels out of my bird feeders?
I have tried the crushed red pepper in the bird seed, and have tried putting vaseline on the pole that holds the feeders....any other suggestions? I will at times hav... See more
How do I tighten the nut on this lamp?
I have a lamp that's 1ft 16in long with the opening of the hole at the bottom that's only 2in wide, so how do i tighten up the bottom nut that's on the inside of the ... See more