Shutter and Slats Coffee Table

2 Materials
2 Days

Last week I showed you my wicker table. I had to make a pallet wood top for the table because I had stolen the glass for this project. ..a table made entirely of recycled materials.
It all started when a friend of mine messaged me and told me that a local salvage yard was putting a bunch of mismatched shutters out in their parking lot under their free tent. I didn't even know they had a free tent. I couldn’t go that night because they close early, hopefully they would still have some the next day.
Well I’m happy to say they did, and I grabbed a bunch. I chose this black shutter for my first shutter project because of the width, 20″ ,which just happened to be the exact same width of the glass from the wicker table. It was fate!
After a good scrubbing, the shutter was cut down to the same length as the glass. Again perfect! The length was right where the natural break of the shutter occurred. I was going to use the black side, but this original blue color on the underneath kind of spoke to me. In order to use the underside, I had to sand off whatever the brown stuff was on the slats, sand the edges where the black paint had sloshed over then touch up between the slats.
A reclaimed piece of 2×4 forms the frame for my shutter. The corners were attached with glue and long decking screws. Once attached, the frame was given a good sanding, especially the pointy corners and any splintered wood then finished with a white wax.
I put the frame upside down and layered in the glass followed by the shutter. With a nail gun, I used 2 1/2″ nails to attach the shutter to the frame. (Avoid the glass!) Just a few nails per side holds the shutter in place. Using scrap wood, attach a small ledge on all 4 sides, butt up against the shutter, then glue and nail into place.
For the legs I used old spindles from a staircase cut to equal lengths of 18". To hold the spindle in place, cut a piece of scrap wood with 45 degree edges as shown and screw into place.
I used a half width piece of pallet wood, mitered at the ends, as a ledge to hold a bottom shelf. Nail or screw into place.
Bed slats were used for the bottom shelf. They were painted with teal chalk paint, lightly sanded, waxed then nailed onto the pallet wood ledge. Of course pallet wood would work just as well.
A shutter would make a very uneven top for a coffee table, the glass finished it off perfectly. If you need more step by step pictures and of the finished project, I hope you have a chance to stop by. You can also check out the table transformation where the glass originally came from.

Since I first posted this project I've now completed 25 different shutter projects. Check out the full gallery here with links to all the fun DIYs.

Suggested materials:

  • Shutter, legs  (salvage yard)
  • Glass top  (thrift store)

Top Hometalk Projects

30 Adorable DIY Ideas For July 4th
18 Fun Ways To Add Glitter To Your Home Decor
15 Unbelievable Ways People Paint Their Walls
Do Your Kitchen Cabinets Need an Update?
13 Spectacular Ways To Display Your House Number
30 Essential Hacks For Cleaning Around Your Home
26 Adorable Ornament Ideas to Get You REALLY Excited for Christmas

Want more details about this and other DIY projects? Check out my blog post!


Have a question about this project?

2 questions
  • Amy Lynn Armistead
    Amy Lynn Armistead
    on Oct 15, 2016

    Where did you get the glass? I need one about that size👍🏻🙂

    • ScavengerChic
      on Oct 15, 2016

      Hi Amy, I don't know if you read the post but this glass was part of a wicker table from a thrift store find. I know Ace Hardware cuts glass but I don't know if they cut the thick glass. Good luck

    • Robin Czaikowski
      Robin Czaikowski
      on Oct 18, 2016

      Glass can be cut to any size you want, at any glass shop in the world.

    • Audrie Platt
      Audrie Platt
      on Oct 28, 2016

      I found a bunch of glass circles in our local Restore for 25 cents each, so I grabbed a few. I glued ceramic feet to the bottoms of some to make cake serving plates. I planned on using three for separate layers of a wedding cake I was making. The top layer had to be a smaller plate so I took it to the local glass shop to have it made smaller (10" down to 8") When it smashed to smithereens we were all shocked. The glass plates were from tempered glass. Now they are used for hot dishes at the table in all my friends houses. Virtually unbreakable.

  • Margaret Adamson
    Margaret Adamson
    on Jun 22, 2018

    This is beautiful. I have a question? I have a glass top coffee table tucked away. When we were using the table everyday use caused debris to collect at the edges and just under the glass. I want redo the table with new glass. What would suggest to seal around the glass to prevent this. I cleaned it every week or more often. I had to lift the glass up from underneath and being rectangular it was difficult, I thought I would break the glass and cleaning the edges of the table caused quite a bit of wear. I didn't realize this when I bought it. I just can't let it go!lol

    Thank you

    • ScavengerChic
      on Jun 23, 2018

      I personally would not seal the edge, that would prevent you from ever lifting the glass again. That being said there is clear caulk on the market that would fill in the gap. You may or may not like the final product

    • Margaret Adamson
      Margaret Adamson
      on Jun 23, 2018

      Thank you

Join the conversation

2 of 42 comments
  • Lori
    on Jun 28, 2018

    I want to try this!

  • Joanie
    on Nov 17, 2020

    Gorgeous!! Rustic and farmy lookin'......shelving underneath, nice place for afghan or magazines. Fits right in!!

Your comment...