Jacob Jennings
Jacob Jennings
  • Hometalker
  • Noblesville, IN

Refined Rustic Floating Shelves

3 Materials
$30
2 Hours
Medium

There are a lot of tutorials on floating shelves. It makes sense, they are very popular. They fill the roles of both function and form. Most of the tutorials teach you to build the bracket first, then cover the bracket with wood. Those are fine, but you can't take the shelf down without completely dismantling it, or destroying it. You can also see the nails or nail holes. This tutorial will show you how to build and hang a shelf that is removable and a bit more refined than most shelves I've seen.
refined rustic floating shelves, shelving ideas


Buy these stunning shelves for yourself by clicking here!


We'll start with the face boards. These are the boards that face out to the room when the shelves are on the wall. I always use select grade boards for this. This shelf is going to be 46” in length, 8” deep and 3-1/2” high. We're going to start by cutting the front face board. I always remove the very end of a new board to get a nice clean edge.
Next, measure out the length of your shelf on this board. This front board will be however long your shelf is going to be. Again, this is a 46” shelf, so we cut this board at 46”.
refined rustic floating shelves, shelving ideas
The next step is to cut the side face boards at 7-1/4". I cut a lot of these, so I have a stop set up on my miter saw at 7-1/4". If you're building a few sets of shelves around your house, I would suggest doing the same. It removes any variation between the length of the sides and will make assembly more streamlined.
Set your Kreg jig for 3/4” material and clamp one of the side boards in as shown. You're going to drill two pocket holes in each side board.
refined rustic floating shelves, shelving ideas
Attach the side face boards to the front face board as shown. Get the edges as flush as possible.
refined rustic floating shelves, shelving ideas
Next, we're going to rip down a 1”x10” board to 7-1/4” for the top of the shelf. The width of this board will be the same as the length of your side face boards. If you don't have a table saw, you could use a 1x8" board which is actually 7-1/4" wide.
Measure, very accurately, the inside length of your face frame. This will be the length of your newly ripped board for the top of the shelf. Cut your board to that length and check the fit as shown in the above photo. It should fit snugly, but not so snug that it makes the boards on each side move.
refined rustic floating shelves, shelving ideas
Drill 3/4” pocket holes in the top board as shown. The spacing isn't critical, but try to get one hole every 12” or so. Don't forget he two pocket holes in the end of the board. Set the board back into the face frame in the same orientation as when you checked the fit and attach it using 1-1/4” pocket hole screws. Try to keep the edges flush as you drive the screws in.
refined rustic floating shelves, shelving ideas
Now we need some pieces for the inside of the shelf. These will support the plywood bottom and provide the cavity we'll need to hang the shelf. If your face boards are 1”x4” material, these spacers should be 2-3/8” wide. You'll need two cut two at 7” long and two at 4-1/2” long. Drill 3/4” pocket holes in the two shorter pieces.
Put the pieces in the shelf as shown. The outside supports(7”) can be nailed into place with a brad nailer. The inside pieces should be attached using 1-1/4” pocket hole screws.
refined rustic floating shelves, shelving ideas
refined rustic floating shelves, shelving ideas
Now we need to cut a strip of 1/4” plywood for the bottom of the shelf. This piece should be exactly the same width as your top board. For an 8” depth, that is roughly 7-1/4”. Measure the length of the inside of the bottom of the shelf. You need the length from the inside of one side face board to the other. Your plywood bottom will be recessed inside of the boards. Next, we're going to cut the plywood bottom to length, put down a strip of glue on the interior spacers and nail the plywood bottom into place.
refined rustic floating shelves, shelving ideas
refined rustic floating shelves, shelving ideas
Now is the time to clean up any edges that aren't flush. I prefer to use a hand plane. You could also sand them flush if they're not too far off. Sand the entire shelf with 120-150 grit sandpaper. If you have a random orbital sander, use that. If you're sanding by hand, remember to sand with the grain of the wood. After sanding, you can apply the finish you've chosen. This shelf will be finished with Minwax Espresso.
refined rustic floating shelves, shelving ideas
Now we're going to build the bracket. The bracket length should be 3-1/4” less than the overall length of your shelf and 2-1/4" tall. This will ensure it will fit inside your shelf. You can use any 2x material you would like. I prefer 2x6 boards because I can get a lot of brackets out of one board.
refined rustic floating shelves, shelving ideas
refined rustic floating shelves, shelving ideas
refined rustic floating shelves, shelving ideas
You will also need three pieces cut to 5-1/2” length. These pieces should have two pocket holes drilled in them. Attach the arms to the long piece as show with 2-1/2" pocket hole screws. This will fit inside the shelf, so make sure to place the bracket arms so they won't hit the spacer pieces inside your shelf. See the video link for instructions on how to mount the bracket to the wall.


Buy these stunning shelves for yourself by clicking here!

refined rustic floating shelves, shelving ideas
The finished shelf!
Here's the shopping list:
1 - 1x4x8 Select Grade Pine
1 - 1x10x8 Standard Grade Pine
1 - 2'x4' sheet 1/4" Plywood
1 - Box 1-1/4" Pocket Hole Screws
1 - Box 2-1/2" Pocket Hole Screws
Finish nails(and nail gun if possible)
Tools Needed:
Miter Saw
Drill
Kreg Jig and bit
Nail Gun (optional)
Random Orbital Sander or sanding block
120 or 150 grit sandpaper
Tape Measure
Pencil
Table Saw (optional)

Suggested materials:

  • Wood  (Menards, Lowes, Home Depot)
  • Pocket Hole Screws  (Menards, Lowes, Home Depot)
  • Stain  (Menards, Lowes, Home Depot)

Have a question about this project?

2 questions

Join the conversation

3 of 14 comments
  • Kate
    on Nov 19, 2016

    Directions for mounting on the wall would be good. Maybe another Tutorial? Thanks

  • Debi53
    on Jul 6, 2018

    Beautiful shelves. Thanks for the tutorial.

Your comment...