Pendant Lamp From Recycled Wood


Make this gorgeous pendant light from some recycled wood with just three tools!
You can make it too!
It's quite easy and minimal tools are required.
Use some pallet wood (preferably oak, or hardwoods).
I found 100 year old recycled Guanacaste wood (similar in color to walnut) that was going to be burned.
Please check out the video for more details on making this lamp.
Subscribe to my YT channel for more projects!
Cheers!
pendant lamp from recycled wood, lighting
I used some recycled wood but you can make it from pallet wood as well
Find a dark wood pallet or if you can't find one you can always stain it easily.
To make the circles glue up two boards to get the width.
I used some recycled wood but you can make it from pallet wood as well
Find a dark wood pallet or if you can't find one you can always stain it easily.
To make the circles glue up two boards to get the width.
Cut the 2 Circles and the Grooves
Cut the 2 Circles and the Grooves
WARNING - PLEASE READ!
This part is a bit dangerous if not operated correctly so please read the instructions twice (or 5 times).
If not feeling safe please do not try this on a table saw.
You can do it with a ordinary handsaw although it'll take a bit more time (not much for one lamp).
If you opt for a handsaw, find one with a wide kerf (thick cut).
Cut two 6'' (15cm) diameter circles and drill them both with 1/4'' (6mm) in the center.
Drill a 1/4'' hole in a center of a board wider than your table saw fence and clamp it to the existing fence on your saw.
Attach the circles (one by one) to that whole with a bolt and wing nut.
Tighten the wing nut tight!!
Raise the blade so the notch is about 1'' (2.5cm) deep. I did this by eye so it's not critical dimension.
Slowly release the wing nut but not making it loose.
Hold the circle so it can't spin, and hold it tightly.
Try to slowly spin the circle thus making the groove.
When finished re-tighten the nut and turn off the saw.
I hereby state that I'm not responsible for any injuries that may happen, please read the warning signs and instruction manual of your table saw before using it. Always think before you make the cut.
Please be careful!
Make a doughnut :)
Make a doughnut :)
Use bigger drill bit so the jigsaw blade can fit in it.
Make the donut shape by cutting the inner part of the lamp's lower circle by making a doughnut.
This will make the lamp efficient by illuminating the table surface.
The doughnut hole is 4'' (10cm) in diameter.
You can skip this part if you don't need the light passing on the bottom part of the lamp.
pendant lamp from recycled wood, lighting
Cut about 15 strips of wood 24'' (61cm) long and 2'' (5cm) wide.
The thickness is around 1/8'' (3mm) and it depends on wood's ability to bend (oak is great for this and can be cut thinner).
You'll need 11 to 13 strips but some may crack when you bend or install them so it's almost necessary to have some extras.
Use push stick for safety because they are very thin pieces of wood.
Bending the Wood
Bending the Wood
Before bending soak the wood in hot water for 5-10 minutes and then carefully place them into the jig you've made.
Oak works best for this, but any wood will work as long it's straight grain hardwood (avoid knots and softwood).
I used Guanacaste wood which is beautiful but a bit too soft for this use.
Drill the holes in an arch so the pencils (colors) can fit inside.
Then make a jig (pictures) and place the soaked strips inside.
Leave them until dry and repeat until you have enough strips.
The strips will spring back quite bit when you take them out but they will be more pliable to set in the grooves easily.
Dry Fitting
Dry Fitting
Dry fit the strips to make sure they enter into the grooves and the lamp looks symmetrical.
Sanding
Sanding
You want it to look nice?
It's Fun time - Sanding!
Take everything apart and sand it smooth for finishing.
120 grit followed by 220 grit sandpaper.
Since it's not a lot of work you can sand by hand if you don't own the sander.
PS Some strips might need some bevels so they can enter together into the groove.
Make this with a block plane (or a knife).
Finishing
Finishing
You can assemble the lamp with glue or keep it without glueing for eventual disassembly.
Apply finish.
I applied wax but it's much better to use some kind of varnish or polyurethane (makes dust cleaning easy).
Hang the lamp from the ceiling to the height desired.
Install a bulb (I like the look of Tesla's style bulbs).
pendant lamp from recycled wood, lighting
I just love the way this lamp looks.
It's light, yet big, but again - very elegant and it looks just gorgeous.
I'm very happy with how this lamp came out and I bet you - you'll be de-light-ed, too.
Please subscribe to my YouTube channel for more video projects here:
https://www.youtube.com/channel/UCIgcC0FXCaKROxx6LHZSZdg
pendant lamp from recycled wood, lighting

Suggested materials:

  • Pallet (oak/hardwood)  (Free at supermarkets)
  • Glue (optional)  (Hardware store)

Top Hometalk Projects

23 DIY Wall Clocks That'll Transform Your Whole Room
13 Essential Repair Tricks That Everyone Needs To Know
15 Genius Curtain Ideas To Instantly Upgrade Your Space
20 Easy Concrete Projects You Absolutely CAN Do!
20 Easy Concrete Projects You Absolutely CAN Do!
29 Of The Best DIY Mirror Projects Ever Made
31 Coastal Decor Ideas Perfect For Your Home
15 Amazing Ways To Get Your Patio All Ready For Summer
17 Faux Brick Ideas For Your Home
18 Fun Ways To Add Glitter To Your Home Decor
16 Creative Ways To Upcycle Pallets
15 Things To Do With Scrap Material
15 Genius Curtain Ideas To Instantly Upgrade Your Space
21 Totally Terrific Things You Can Do With Doilies
15 Things To Do With Scrap Material
Andrea Arzensek

Want more details about this and other DIY projects? Check out my blog post!

Go

Have a question about this project?

2 questions
  • N. G. Londonderry
    on Feb 6, 2017

    Is it the bulb itself that supports the lamp ?

  • Debbie
    on Feb 6, 2017

    What kind of saw did you use to make 1/8" strips? I want to make this project. It is so beautiful.

    • Andrea Arzensek
      on Feb 6, 2017

      It's a circular saw mounted under the table. It was back then when I didn't have proper table saw, but that didn't stop me. You can make anything. Thank you for your comment Debbie!

Join the conversation

3 of 55 comments
Your comment...