DIY Platform Bed With Floating Night Stands

4 Days

Be sure to check out the video for more details.

For the past year or so I have been receiving a ton of request to make a platform bed. The whole time I actually needed one, but for whatever reason, I been putting it off. Well, I finally gave in and went to work. So glad I did because I thought it actually enhanced the space and have a luxury feel to it.

Get the KING plans here.
Get the QUEEN plans here

-----------------------------Price Breakdown-------------------------------------
King BED and electronics
- Wood $219
- Accessories brackets etc.. $65.00
- Electronics $165
Total investment = $449.00

After sorting through all the lumber at my local HD store. I manage to find enough lumber that I could work with. I started this project with a rough sketch up of what I wanted.
Although this project can be made with a circular saw, I would highly suggest a miter saw to speed things up. The key to being successful is attacking all your projects with patience.
If you like to build this; I have a detailed set of PLANS this project. After all the lumber was cut down to size. I set up shop outside to begin the sanding process. Prepare for hours of sanding and be sure to wear a mask and safety glasses. I sand the bed down with 80 grit sand paper first, then 120 grit followed by 220 grit to wrap things up.
Next, paint or stain the bed frame whatever color you prefer. I chose black.
Due to the length of the headboard, I had to attach a small section to extend the 8ft sheet of plywood. I then painted the bottom section of the plywood to match the bed frame.
If you have any assistance around feel free to ask for help. I didn't have that luxury at the time, so I took advantage of the clamps I had on hand. I started from the top down. It would have been easier to start from the bottom up. The reason I took the route I did, was simply because I didn't want to be off by a fraction. Which would result in making cuts later on, when approaching the end.
After, clamping the lumber in place, I then screwed a couple screws in place. Checked that everything was visually ok then added two screws every 2 feet. I repeated the process until I reached the end.
I used one coat of dark walnut danish oil additional coats could be applied if a darker look is required.
With the headboard being so massive, it covered the existing wall receptacles. It made sense to add outlets in the nightstands. After identifying which piece looked less attractive I selected it to be the back of the nightstand. Then I cut out the opening for the electrical work box .
Building the floating nightstand
I used a dowel jig from Rockler to make accurate holes for the dowel pins. You have to be patient with dowels a fraction off could cause your workpiece to shift. Which could be very frustrating. The next option is to use screws and fill the heads in with wood filler. Either route you take be sure to use wood glue and clamps.
Mounting the nightstand
After allowing enough time for the glue to dry. Clamps the nightstand at the desired mounting height. I chose to mount them approximately 2 inches below the top of the mattress. Next, drill 4 pilot holes from the back of the headboard. These will be the mounting hole. To clarify the piolet hole should not exit out the nightstand (this should only mark the back). While the nightstand is still mounted with the clamps. Trace out the hole for the electric box on to the headboard, drill a hole for the small on/off switch and drill an angled hole at the bottom into the headboard for the puck light. Repeat this process for the other nightstand.
Now, remove the nightstand and drill out a 1/4'' hole for the bolts to pass through. Then install threaded inserts into the in the back of the nightstand. Be sure to add a stop to the drill bit to prevent going all the way though.

Applying top coat
Appy whip on polyurethane or a top coat of your choice. I used two coats of this a third coat would be even better. I sanded between each coat with 400 grit sand paper.
Adding puck lights
After researching online trying to find low profile puck lights. It seems as if all the wireless options had mixed reviews. I end up settling on a wired kit, to be honest, I'm not fond of maintenance replacing batteries etc. So this kind of worked out. The set I used can be found here on amazon.
I cut the connector off the wire and pass the wire through the hole previously drilled. Then screwed the lights in place. 
I use corner brackets in all 4 corners to assemble the bed frame. Then, installed the bed slats support. By the time I reached the middle frame I realized that I have forgotten to pick up enough brackets. So I used what I had on hand.

I use brackets on the inside and the outside of the bed. You could add as many as you like, 4 seems to do the job for me
 Each trim had four 1.5in corner brackets on the interior and 4 1in brackets on the outside. At the foot of the bed, I used mending plates to attach the two intersecting lumber. This method worked out very well, keeping the two lumber even with each other.
Once the frame was done it was time to center it up and attach it to the headboard.
End Results.
Night Stands
Thanks for checking out this project. If you would like to build your own I have a detailed set of plans.

-------------------------------------Material used -------------------------------------


Note: Wood may not be actual size listed below.  For example (2 by 4 is actual 1.5 by 3.5) 4
- ( 16) 2 by 8 Lumber  (headboard, bed frame and bed trim)
- (1) 2 by 12 lumber (top and bottom night stand) 
- (1) sheet or 3/4in (19.05mm) plywood a small piece 
- (2) sheet of  1/4in (6.35mm)  plywood
- (10) 1 by 4 (25.4mm by 101.6mm) lumber 
- (4) 2 by 4 (50.8mm by 101.6mm) Lumber 

Other accessories----------------------------------------
- (4 packs) Corner brace (outside of the bed trim and inside bed foot) 
- (2 packs) Corner brace (inside the bed  trim ) 
- (1 packs)  Mending plate (bed foot frame) 
- L- brackets for the bed frame  
- 1/4in – 20 inserts (to mount the night stand) 
- 1/4in round head Philips 3in long
- 1/4in Washer 
- #10 Screws (2 in)  
- #8 Screws (1.5in) 

Finish ---------------------------------------------------------

- Danish oil 
- Wipe on poly
- Foam roller 
- Black paint 

LED, Electrical, and wire ------------------------------

- Puck Lights 
- Led Strip 
- Round switch 
- (2) Outlet with USB ports 
- (2 ) outlet cover 
- (2) workbox [junction box] 
- Electrical wire(for the outlet) 
- Receptacle Tester - 
- 22 gauge wire (for the puck light switch) 
- Extension cord

Top Hometalk Projects

30 Gorgeous Ways To Keep Your Home Organized
31 Amazing Furniture Flips You Have to See to Believe
30 Stylish Update Ideas You'll Want To Use For Your Bedroom
Check Out These 30 Incredible Sharpie Makeovers
Instantly Upgrade Your Living Space With These Amazing DIY Ideas
30 Ideas To Make Your Office Look Great
15 Clever Ways To Repurpose Old Light Bulbs
25 Adorable Ornament Ideas to Get You SUPER Excited for Christmas
3 Creative Eye Catching Rug Projects That No One Else Has!
Cut Up Some Pallets For These 20 Amazing Ideas
21 Ways to Have More Polka Dots in Your Life
18 Wintery Wreath Ideas That You'll Want To Make For Your Home
Storage Hacks That Will Instantly Declutter Your Kitchen
30 Creative Ways To Repurpose Baking Pans
Dollar Store Gem Backsplash

Have a question about this project?

3 of 5 questions
  • Jod5413
    on Jul 1, 2017

    Your platform bed with headboard and floating nightstands is gorgeous and I want one for me! Being the bed maker, the only thing I might consider asking about changing would be rounding of the corners at the bottom of the bed frame. My knees would surely appreciate that feature!
    • Eddie
      on Sep 12, 2019

      I made one several years ago by remaking an old water bed frame. on most water beds there is a padded rail that goes on the top of the side boards to protect you getting in and our of the bed, no side rails so we wasn't going to use them, but, we realized that they worked perfect on the platform edges to make them shin safe,lol. just an idea for ya, easy to make, 1/8" plywood and make a three sided box to fit over the edge of the platform, use angle braces inside the frame of the 3 side rail covers. then place how ever thick of foam pieces you want so that it covers all three sides and place material over it , the material can be attached with staples at the inside edge of the framework, then just side them onto the platform. be sure to give a bit of space for the foam and matterial and brackets to clear the platform edges, but not to much or it will fall off all the time, you have to keep it snug. fit them all the way around and problem solved.

  • Jody
    on Jul 2, 2017

    How many times did you hit your shins against the platform before you remembered where it was 😬? Had one years ago, loved because it was about 4" wide and you can set drinks, eyeglasses, books, all kinds of clutter there. But it took a little getting used to where it was. You did a beautiful job plus an excellent job explaining what and how you made it. 5 gold stars!!!
    • Arlene
      on Jul 15, 2017

      I really love how your bed came out. Maybe take some of those foam swimming tubes cover the edges and corners. I had to get rid of a bedroom set because I kept hitting my legs.

  • Michelle Schumacher
    on Sep 5, 2019

    I love it! It looks so simple but once you stated the hours of sanding...yikes! Does the mattress slide around? Or is there a way for it to stay centered?

    Your work is beautiful.

    • Eddie
      on Sep 12, 2019

      Michelle, the mattress sits down into the platform, the platform is sized so that it is like a frame around the mattress, therefore holding the mattress in place.

Join the conversation

2 of 87 comments
  • Wanda
    on Jun 10, 2019

    Beautiful bed. Wonderful workmanship. You definitely know what you're doing. I made my daughter a loft bed years ago so I know what you mean about all that sanding. Keep posting your projects. You're a wonderful inspiration.

  • Beth
    on Aug 2, 2019

    I have to say... I'm impressed! Thank you for showing the process for putting all the parts together. The electrical is tricky, but makes the bed. I may redo the headboard so that it's not so heavy. I was stumped in a couple of spots trying to build my own platform bed devised by moi. I know it's not your ultimate, ideal bed, but tweeked in the right places, it will be for me and my fiance. He will be helping! Mine will be different, but using some of the ideas I've seen here. I'm grateful for your documented work. I'm a commercial interior designer, inventor, artist, and avid DIYer. And yes, I am a woman. I'm anxious to get started! Thanks again.

Your comment...