DIY Quilling Tool

2 Materials
5 Minutes

When you're home & garden DIY'ers that repurpose and upcycle as much as we do - whether it's a reno or craft project - it only makes sense that we would endeavour to do the same when it comes to our tools!

While I'm overseeing an accessible bathroom renovation at my Mom's house, I have some time to spare. Hubs bought me a package of construction paper to take with me so I could try my hand at something I've

diy quilling tool

Raid the Junk Drawers

Being somewhat of a MacGyver of DIY (I get that from Hubs), I raided a few of the junk drawers in my Mom’s house and found just what I needed to make my quilling tool.

diy quilling tool

The Keepers

On my scavenger hunt I found a few of those mechanical pencils that hold thick lead. The prongs of the lead sleeve open up pretty wide, so all I had to do was find something to replace the lead with to create my DIY quilling tool.

diy quilling tool

A trip to the bathroom garnered me a cotton swab (a.k.a. a Q-tip). I also got scissors in the kitchen drawer, a utility knife in the tool box and a seam ripper in my Mom’s sewing box to round it all out.

diy quilling tool

Let's Make a Quilling Tool!

The Q-tip is perfect for this tool because the spindle is made of extruded plastic which is hollow through the middle.

To start, cut the ends off the Q-tip, leaving you with just the spindle.

diy quilling tool

The ends may be sharp or have some burrs, so sand them down until smooth. I only did one end to save time.

Depress the top of the mechanical pencil so the lead sleeve opens up. Insert one end of the spindle into the sleeve and release (ensuring the smooth end is exposed if you only sanded one end like me). This will stabilize the spindle and give you something to hold onto to as it's cut in the next step.

diy quilling tool

Cut Slit into Spindle

Grab the utility knife and extend the blade as shown. Insert the point of the blade into the middle of the plastic spindle about 3/8" from the end.

diy quilling tool

Gently rock the blade back and forth until you cut a slit to the very end (be sure to watch the video at the end of this post to see how this is safely done).

Make sure to only cut through one side; this will create the opening that grips the quilling paper.

Widen the Gap and Test

Use the seam ripper to widen the gap so you have a slightly wider slot to accommodate the paper. You should be able to guide the sharp part of the ripper along one side of the cut to shave off a sliver of plastic.

diy quilling tool

Although I cut my opening 3/8" long, you can customize the length of the slit to accommodate the width of any quilling paper! The beauty of this tool is that you can make a few different tips to quill. You can even make it two-sided so you can flip it around, or widen one of the slots for thicker paper :)

Test the slot out with a piece of quilling paper. If you are satisfied with it, move onto the next step. If not, you can always finesse it or cut the end and start over again.

Shorten Spindle

Now shorten the spindle. I cut it to just under 3/4″. An added bonus of shortening the spindle is that it gives you extra material to customize more tips with different length slots if needed!

Put the spindle back into the mechanical pencil with about 3/8″ inside the sleeve and 3/8″ below the prongs. This exposes just enough of the spindle to insert the quilling paper.

diy quilling tool

Hey, I just realized that even after the transformation you can still call it a Q-tip (short for quilling tip). How ironic is that?

Take Your New Tool for a Spin!

Insert a piece of quilling paper into the slot in the spindle. ♪ You spin me right 'round baby right 'round, like a record baby, right 'round 'round 'round♫.

diy quilling tool

The prongs of the lead sleeve will act as a bumper as you roll the paper to keep it relatively even. How simple was that?!

diy quilling tool

Pull the wound paper off right off the spindle and you have your first quilled circle! Or an exclamation mark

Exclamation Mark!
Exclamation Mark!

An Important Question

Quill YOU try It?

diy quilling tool

I sped up the video attached so it’s only around a minute long, but it literally took under 5 minutes to complete. Watch it to see for yourself!

Have fun with your new quilling tool!

diy quilling tool

Get your DIY mojo on and subscribe to Birdz of a Feather here! You can also follow us on:





Suggested materials:

  • Mechanical pencil  (
  • Cotton swab  (
Birdz of a Feather

Want more details about this and other DIY projects? Check out my blog post!


Have a question about this project?

Join the conversation

Your comment...