I'm currently finishing my basement. There are two halves to my basement and they are separated by a very interesting incline. I don't know whether I should build some sort of steps or if anyone has a good idea for a rubber transition. It gets pretty slippery and not manageable for older people. I'm leaning towards putting a step or two in but I'm not really sure how to do it. If you could take a look at the picture and let me know if you have a suggestion, I would appreciate it. Thank you.
I'm going to be removing that peel and stick. It'll just be cement until I figure out what to do.
The house was built in 1900 so the top of the incline isn't level and dips and certain places.
You can purchase a transition threshold that is for two different heights of flooring. It is smooth on top but adjusted on the bottom. You can get a wooden one and stain to match one of the parquet tones.
For a simple and quick fix....I would remove the tiles on the incline and glue down rubber flooring like they have in gyms and fitness centers. Various styles and colors available. Slip resistant.
You should be able to get the thickness you need. If it does need to be beveled....you can use a razor utility knife to trim it or coarse sandpaper to get the thickness. Do not bevel the top but bevel the bottom. Once it's glued down you will have a smooth transition.
After taking up the tile, I would put in a step (that's a pretty good incline to just slope the floor). Make sure to put in either a handrails of grab bars so older people can navigate it safely. After you put in the step, there is self leveling compound that you can pour on the floor. Just remember to put something at the step to keep the leveling compound where you want it.
We had that terrible ugly rental green carpet on our stairs to the basement. It was the last carpet to come out. I then painted the steps and used some anti skid... See more
My very old and faithful Hoover vacuum sadly gave in and stopped working after about 25 years. It's time to move on and find a replacement.I'm not very informed about... See more
I found some what it appears to be cat liter stain spots on my bathroom floor and can't seem to get rid of it. Any suggestions on how I can get them out? Thanks!
My honey maple floors have a rough surface. If is spot clean, it leaves a "patch" on the floor that shows up from a distance. Cleaners leave streaks. How do I clean... See more
There is old, nasty carpet in my dining room/eat-in-kitchen! Gross!!! A new floor is not in the budget for a few years. i'd like to pull up the carpet, paint the... See more
i am renting a house and definitely do not want to put money into it. I have hard wood floors throughout the rest of the home which are the newer tight fitting ones.... See more
My husband is building a 3 season porch and we are trying to decide on flooring. We are going for a rustic outdoor feel and want to go with lpv but are having trouble... See more
I have vinyl flooring in my guest bath and utility room. It is about 15 years old. It is white with a small black diamond centered in each square. Over the years, the... See more
Hello, I had a Saltillo tile floor put in 4 yeas ago. The installers did not put the proper Finnish on the floor and looks terrible. Can I strip and put a new Finnish... See more
After painting our knotty pine wall we discovered after pulling off the painters tape that some of the shellac based primer seeped under the tape & onto our newly... See more
I live in a mobile home and have carpet in my living room and dinning room. The carpet has these reoccurring black stains. What would be least expensive way to cover... See more
I'm hoping someone may have some advice on a project that I am considering; I would like to try to apply contact paper to the concrete floor in a small basement room.... See more
My new vinyl flooring will sit slightly above the brick hearth in front of my fireplace but what material do I used where the flooring ends and hearth begins?
I need a quick inexpensive solution. We are not able to raise the floor at this time. (Converted garage to livingroom)We took out a wood box to repair water damage... See more
My house is a 1933 and I ripped all the carpet our as soon as I moved in, August 2016. Much to my surprise, it is the original wood floors. I am a single Mom and... See more
Our floors are old and have fine line cracks running across some of them, some from one to halfway across the whole floor, I guess from things being dropped on them.... See more
You can purchase a transition threshold that is for two different heights of flooring. It is smooth on top but adjusted on the bottom. You can get a wooden one and stain to match one of the parquet tones.
I got mine at Lowe’s. Ace hardware has a lot of odd sizes as well.
After u pull up flooring even it with cement or plywood to make even then put flooring
For a simple and quick fix....I would remove the tiles on the incline and glue down rubber flooring like they have in gyms and fitness centers. Various styles and colors available. Slip resistant.
https://www.google.com/search?q=glue+down+rubber+flooring&source=univ&tbm=shop&tbo=u&sa=X&ved=0ahUKEwiCp8Ci_NngAhUMWa0KHRs8BAUQsxgIKw&biw=1536&bih=740
Do you know the best way to bevel the top so there isnt a lip?
You should be able to get the thickness you need. If it does need to be beveled....you can use a razor utility knife to trim it or coarse sandpaper to get the thickness. Do not bevel the top but bevel the bottom. Once it's glued down you will have a smooth transition.
After taking up the tile, I would put in a step (that's a pretty good incline to just slope the floor). Make sure to put in either a handrails of grab bars so older people can navigate it safely. After you put in the step, there is self leveling compound that you can pour on the floor. Just remember to put something at the step to keep the leveling compound where you want it.