Porch Daydreamer
Porch Daydreamer
  • Hometalker
  • Davidson, NC

How-to Install LED Under Cabinet Lights in the Kitchen

5 Materials
$175
4 Hours
Advanced

Looking to update your halogen, fluorescent, or xeon under cabinet lights to LED? Here's how to install LED light bar fixtures using your current under cabinet wiring!

how to install led under cabinet lights in the kitchen

Beautiful new LED lights make for a brighter working surface.


PLEASE VISIT THE LINK AT THE BOTTOM FOR MORE DETAILS AND PICTURES.

how to install led under cabinet lights in the kitchen

Before Installing LED Under Cabinet Lighting

First and foremost, this is NOT and I repeat NOT for a novice DIYer. This is for someone who has tackled at least a couple of the following and done it more than once:



  • Installed outlets
  • Added dimmer switches
  • Hung ceiling light fixtures or fans


You should be familiar with a few other things:



  • Circuit breakers
  • Wire stripers
  • Electrical tape
  • Wire nuts


Also, if you aren't able to work in small spaces, upside down, and with little parts - this isn't for you!


Last but not least, this became a TWO PERSON job. I highly recommend recruiting a helper to help hold the fixture while you attach.

how to install led under cabinet lights in the kitchen

TURN OFF CIRCUIT BREAKER TO UNDER CABINET LIGHTS. 


Step 1


Remove your old under cabinet lights. This was simpler than I thought it was going to be. These lights came with the house so I really didn't know what I was going to encounter.


The diffuser dropped down to expose the screws that needed to be removed. I was accustomed to dropping the diffuser to change the bulbs. 

how to install led under cabinet lights in the kitchen

All that needed to be removed were 2 screws and two wing connectors (tan in the picture). 


First remove the wing connectors to drop down the panel with the wiring. Just the act of turning mine horizontally let the panel drop. 

how to install led under cabinet lights in the kitchen

Step 2


Remove all wire nuts to release the connections. Those are the orange caps on the wires.


My previous lights had a transformer, which I removed as well. It wasn't needed with the new LED lights and my existing wiring.

how to install led under cabinet lights in the kitchen

With a power drill, remove the last two screws that mount the fixture to the cabinet and remove the final piece.


All that will be left is exposed wires. See how SCORCHED the underside of the cabinet is from the xeon lights?


Since I have moulding at the base of my cabinets, I didn't need to touch up the paint or fill the holes. I left it as you see it and installed the new lights.

how to install led under cabinet lights in the kitchen

Step 3


Follow the manufacturer's instructions to pull parts out from inside of fixture. Basically that involved removing the diffuser and 2 screws. Easy!


Hold fixture up underneath the cabinet and decide where the wires will be pulled through and where you want to hang the fixture.


Sorry I couldn't photograph this part at the same time!


Using a pencil, mark through the key holes. The smallest area is where the screw will be placed. 

how to install led under cabinet lights in the kitchen

This will help you decide which hole to punch out for the wires. Punch out wire hole with a flat head screw driver.

how to install led under cabinet lights in the kitchen

Step 4


This part is REALLY important and don't skip it! You MUST install the strain relief so the wires are protected.


Just feed it through the hole. Remember the nut is on the backside of the fixture or the wall side. Tighten with long nose pliers.

how to install led under cabinet lights in the kitchen

Hold base fixture up to the underside of the cabinet and pull through wires. Your long nose pliers will come in handy to straighten wires and pull on them.


Make sure to grab the actual wire when pulling and if you damage the wire insulation repair it with electrical tape. With your power drill and Philips head attachment, screw in screws where marked on the underside of the cabinet to hold base fixture.


Leave about 2 to 3 turns, so it's not completely flush with the cabinet. If you have a little trouble getting the wood screws to grip, drill a small pilot hole with a 1/16" drill bit.


Some of mine went in easily and others didn't. 


Attach base fixture by pulling the fixture forward to lock into the smallest part of the keyhole. Then tighten down the screws to the base of the cabinet. 

how to install led under cabinet lights in the kitchen

Then using the two screws that come with the fixture, tighten the strain relief connector to secure the wires.

how to install led under cabinet lights in the kitchen

Step 5


Firmly push wires into the quick connect nut on the fixture: white to white, black to black, and ground/copper to green.


IF you pull down one of your fixtures and see 2 white, 2 black, and 2 copper ground wires it's OK. Two of my fixtures had this to create the connections between the light fixtures.


The red quick connectors have TWO spots for wires, so you just follow the same process matching each wire type.


On the 2nd fixture with the sets of 2 wires, I ended up using my wire cutter/striper because these wires were so long. Cut and strip the wires to work with the space you have.

how to install led under cabinet lights in the kitchen

Step 6


Flip circuit breaker and test to make sure the light turns on. If not, flip the breaker off again and check connections are secure. 


Next, get your partner! This is where you need another set of hands.


Using the provided screws and washers, using a power drill or Philips head screw driver screw LED light panel to the base that is attached to the cabinet.


An issue I ran into with the 12 inch fixture is it was very hard to get the light bar attached. 


The quick connector nuts take up a lot of space and you can see the fixture bows slightly.


There wasn't anything I could do about this! On the longer fixtures, this wasn't an issue so I'm showing you worst case scenario.

how to install led under cabinet lights in the kitchen

Step 7

Attach the diffuser over the light panel.


YOU'VE DONE IT! Your neck and back are sore, fingers raw, but you did it! Now onto the other 3 LED under cabinet light fixtures that need to be installed!

how to install led under cabinet lights in the kitchen

TIP: Every time you finish a fixture, flip on the circuit breaker to make sure each fixture you've installed is still working!


I ran into an issue where ONE white wire didn't clip into the connector properly, so the first light suddenly didn't work.


So check those connections, before attaching the LED bar to the base. 

Any price and availability information displayed on [relevant Amazon Site(s), as applicable] at the time of purchase will apply to the purchase of this product.
Hometalk may collect a small share of sales from the links on this page. More info

Top Hometalk Projects

15 Genius Curtain Ideas To Instantly Upgrade Your Space
21 Totally Terrific Things You Can Do With Doilies
16 Creative Ways To Upcycle Pallets
15 Things To Do With Scrap Material
The 15 Coolest Ways to Reuse Pipes in Your Home Decor
15 Amazing Things You Can Make With Dollar Store Gems
15 Quick and Easy Gift Ideas Using Buttons
No Way! These Pops of Color Were Made With Dollar Store Items!
11 Unexpected Ways to Use Spices in Your Home
31 Amazing Furniture Flips You Have to See to Believe
31 Space-Saving DIY Ideas That'll Keep Your Home Organized
If Your Stairway Walls Are Empty, Here Are 25 Ways To Change Them Now!
15 Kitchen Updates Under $20
30 Ways To Use Old Jeans For Brilliant Craft Ideas
23 DIY Wall Clocks That'll Transform Your Whole Room
Porch Daydreamer

Want more details about this and other DIY projects? Check out my blog post!

Go

Have a question about this project?

Join the conversation

2 comments
  • Jim Cox
    on May 28, 2019

    In the 2nd and 3rd pics of step five: You have the wires on the wrong side of the cable clamp, and you have the wires themselves in the clamp (without a cable jacket). There is a potential for shorting with this. I'd personally go a step further and install an insulating bushing on the back side of the clamp as well. I dont know if that part is code or not (don't have my 2017 book with me). These clamps are made for BX type armored cable, but they will work on NM romex jacket. Since the fixtures are part of the house, you may get dinged for this when you sell it IF the inspector is any good. Either way good luck : )

    • Jim Cox
      on May 29, 2019

      You mis-used the clamps. If it all works I guess you can leave it. The Mfr may not be aware of electrical codes, and more and more there's a serious language barrier with off-shore goods. Glad you are enjoying your lights : )

Your comment...