How to attach old door knobs?
How does one attach old wooden doorknobs with metal bars between knobs to empty holes in the door? The knobs need not turn as there are ball catches on door frames that keep doors shut by themselves. Some holes are perfectly round and some are odd shaped where old knobs used to be. Been trying to figure this out for four years.🙏
Related Discussions
How do I extend this door?
I have these wonderful old doors, they are the right width, too short. How do I make them work?
Closet doors for 95" tall opening
Hello everyone, I'm looking to update my closet doors to be bifold wooden doors, but strangely the opening of my closet measures to be 95" tall, and the current door... See more
How can I resize a screen door?
I got a very old screen door. It is made of 2x4's and put together with tongue and groove. How can I get it apart w/o tearing it up!
Need a quick temporary "door" for a hallway with a high ceiling?
I am looking to block the top of a staircase with a temporary door to keep cats out of the first floor. the problem I am having is that the ceiling is very high, 90"... See more
How do I go about putting new doors on a closet that ends at a wall?
This question has bothered me for a while. When we moved into our house the closets in the small upstairs bedrooms had cheap bypass doors on them. Needless to say, th... See more
Squeaky cabinet doors
I recently painted my kitchen cabinets and put on new hinges. They are now making an annoying squeak every time they're opened and closed. Would appreciate any advi... See more
Well, with the very very old doorknobs in my house they attach to each other through the hole in the door and then their face plates go over to cover the hole and hardware.
Are the wooden knobs in pairs? Does one of them have a semi long rod/shank coming out of it and the other just has a hole in the back of it the same shape of the rod/shank? If so they are a door knob set and you should just have to put face plates on them, feed the rod/shank through the hole in the door and put the other one on the rod/shank. Tighten down the lock screw in the one without the rod/shank onto the rod/shank and then screw the face plates into the door to keep them from moving. If the knobs aren't pairs you will have to find a rod and face plates that you can use to fasten the knobs to the door.
Face plates go on the door leaving the holes. Some old door knob shafts are threaded and the knobs screw on the shafts. This was for different thickness of doors. The knobs have a small set screw to tighten them on the shaft. If the knobs do not screw on and the shaft is smooth then the knobs just tighten on the shaft with the set screw.
If they are circa 1800s look at the side of the door, is there a long thin rectangular cut which accepts a a skeleton key...... https://www.houseofantiquehardware.com/antique-rimlock-horizontal-porcelain-set-a?utm_source=froog&utm_medium=cse&utm_campaign=gdf&partner=froog&CAWELAID=120035490000010381&CATARGETID=120035490000027848&cadevice=c&gclid=Cj0KCQjwoInnBRDDARIsANBVyASYlLhFGGTUMrS7q143K6Y83ckKBpolmayqRcGc7GUY5eLgWqZakEAaAv8jEALw_wcB
1900s mortised sets.... https://www.amazon.com/Prime-Line-2495-Mortise-Classic-Bronze/dp/B00CTHSV4O/ref=asc_df_B00CTHSV4O/?tag=hyprod-20&linkCode=df0&hvadid=193154321880&hvpos=1o1&hvnetw=g&hvrand=3093816762381346439&hvpone=&hvptwo=&hvqmt=&hvdev=c&hvdvcmdl=&hvlocint=&hvlocphy=9033057&hvtargid=aud-643191255296:pla-335349972404&psc=1