Resand a Walkway With Polymeric Sand

2 Materials
$30
1 Day
Easy

All good things must come to an end; nothing lasts forever. Today that sentiment is twofold: we've updated our logo and are replacing the sand in our front walkway!


After noticing some weeds starting to take hold in the joints between our pavers and some erosion over the years, it was time for joint replacement with new Polymeric sand.

resand a walkway with polymeric sand

The bag you see above was left over from when we initially sanded the walkway 11 years ago. We kept it for touchups which we never had to do! It’s incredible that it lasted as long as it did. I’m not sure if that’s the norm, but if you have used Polymeric sand, leave us a comment to let us know what your own experience with longevity has been! Keeping the bag in a tight air-sealed container will help it last (if you don’t keep it air tight it will get clumpy and be unusable).


Don’t Do As We Do!


Hubs used the old product and was almost finished the walkway when he ran out of sand! He had to run out in the middle of the job to find a replacement (the one we originally used was discontinued)!

Hubs had to remove all the sand and start all over again. Don’t you hate when a product you LOVE is no longer available?

resand a walkway with polymeric sand

Before you Start


If you're not familiar with polymeric sand, we explain the benefits on our blog. Don't apply polymeric sand if the surface is wet or damp; the binder will activate making it impossible for the sand to flow into the joints.


Wait to begin the job until the weather forecast is clear of rain for at least a day (this will depend on the product you buy so check the instructions)! If it rains when you're in the middle of resanding the pavers, polymeric sand will harden on the surface and ruin them! The temperature should be above 0 degrees celsius (32 degrees fahrenheit) during the 48-hour drying period.


Put on appropriate safety gear: a mask and goggles will keep fine particles of sand out of your eyes and lungs! This was me getting up close and personal with the pavers 11 years ago. I laid the patio and did the first sanding back then, so it's only fair that we swapped and Hubs took the lead this time!

resand a walkway with polymeric sand

You’ll need a scraper, a stiff broom and a few buckets to separate the old sand from the weeds.


Out with the Old and In with the New


The prep work is the most time consuming: you must have a clean, dry surface and joints. Unfortunately with polymeric sand replacement, you can’t just uproot any weeds and top it up. You have to completely remove all the pre-existing sand in the joints and start fresh.


For this step, Hubs had to get down and dirty with a scraper to remove the old sand between the pavers.

resand a walkway with polymeric sand

Hubs did all the work by hand. Some sites advise using a pressure washer for this step to help blast away at the sand. However, I don’t think that’s a good idea for a few reasons. First, you run the danger of disturbing your base/shifting your pavers. Secondly, you will have to wait a day while the surface dries before you can reapply your new sand. Remember polymeric sand and moisture don’t mix until after it's in the joints!


Hubs used a leaf blower to ensure all the debris was clear of the joints. We’ve never tried it, but a wet/dry vac might also be useful in removing the sand after scraping – instead of sweeping up by hand. At the edges, you can see that we’re right down to the high performance bedding underlay:

resand a walkway with polymeric sand

How to Apply


Hubs pours sand starting at the upper right side of the walkway. Concentrate the pouring and sweeping in each area before moving onto the next (i.e. don’t spread it out over long distances).

resand a walkway with polymeric sand

Spread the polymeric sand evenly over the joints, using a broom, ensuring the joints are filled completely. A smaller broom helps get into narrow spaces, like beside our front step.

resand a walkway with polymeric sand

Hubs transfers sand from the bag into a bucket first so it’s easier to pour small sections. However, if you have a large area – such as a driveway – you’ll probably want to pre-distribute the bags across the surface and pour directly from the bags as you go.

resand a walkway with polymeric sand

To ensure the sand doesn't form a haze on your pavers before it's wet, head to our blog to see our tips (below this post where you see our logo).


Wetting the Joints


Set the spray nozzle to ‘shower’. Hubs tests it out on the lawn first before starting. Once you start, you can’t stop in the middle; wet the entire project without interruption.

resand a walkway with polymeric sand

Ensure that the wetting of one section is finished before another section is started. Starting from the bottom of the slope, shower each section for 30 seconds.

resand a walkway with polymeric sand

Repeat the process on the same section again until the joints are fully saturated. Avoid excess flooding of the surface which could cause unwanted runoff! Move onto the next section and repeat until done.

Hubs brought out the leaf blower once again to blow any excess water off and into the joints. This also helps prevent a possible haze.

resand a walkway with polymeric sand

This time he started at the top and worked his way toward the bottom to draw water down the natural slope of the walkway.

resand a walkway with polymeric sand

Check for Saturation


Insert a screwdriver or key into a joint to verify that the water has penetrated at least 1 1/2″ inches deep – much like putting a toothpick into a cake to check for doneness.

resand a walkway with polymeric sand

Hubs was satisfied that the water had saturated deeply enough, so he patted the sand back in place.


Technology has improved over the last decade. The product we used this time becomes water resistant after only 90 minutes, whereas previously there couldn’t be rain in the forecast for several days after completion.

Lessons Learned


Purchase a product recommended by the manufacturer of your walkway pavers. In all honesty, I wish we had taken more time to research the product first (more about that on the blog). It never seems to works out well when you jump into a project spur of the moment!


If your stockyard already carries the product your paver manufacturer recommends, see if you can look at the actual colour before purchasing. Stockyards will have samples of stone you can look at before purchasing, but I’m not sure if that applies to sand too! If it does, take advantage of that to make sure you’re happy with the colour.


Anyway, before you go to the effort of replacing polymeric sand, do your own research and chase after the best product, and price, for your own application.

resand a walkway with polymeric sand

If you want to stay on top of new home and garden ideas, get your DIY mojo on at Birdz of a Feather and subscribe to us here. You can also follow us on:


Pinterest;

Facebook: http://bit.ly/BirdzFB

YouTube: http://bit.ly/BirdzYT

Instagram: http://bit.ly/BirdzIG

Suggested materials:

  • Polymeric Sand  (Stone Yard)
  • Buckets  (Already had)

Top Hometalk Projects

30 Creative Ways To Repurpose Baking Pans
23 DIY Wall Clocks That'll Transform Your Whole Room
30 Great Jar Ideas You Have To Try
16 Ways to Showcase Your Herb Garden
31 Amazing Furniture Flips You Have to See to Believe
14 Cool Ways To Upholster Chairs That You Can DIY
31 Super Cute & Easy DIY Ideas For Your Kitchen
18 Fun Ways To Add Glitter To Your Home Decor
13 Essential Repair Tricks That Everyone Needs To Know
30 Genius Ways To Make The Most Of Your Closet Space
23 DIY Wall Clocks That'll Transform Your Whole Room
31 Amazing Furniture Flips You Have to See to Believe
15 Quick and Easy Gift Ideas Using Buttons
30 Ways To Use Old Jeans For Brilliant Craft Ideas
17 DIY Decor Ideas To Get The Party Started
Birdz of a Feather

Want more details about this and other DIY projects? Check out my blog post!

Go

Have a question about this project?

2 questions
  • LeeEllen Zahorsky
    on Jul 9, 2019

    can this product be used in the joints found in concrete sidewalks? the joints in my sidewalk have cracked and also shows some soil can this polymer still be used? this product is exactly what I need

  • Michelle Bellin
    on Jul 9, 2019

    can this be used for a brick walkway? The stuff between the bricks is terribly eroded & I want to fix it for my 80year old moms.

    thank you

    • Birdz of a Feather
      on Jul 10, 2019

      I think it could, but it's best to check with the manufacturer of the product you choose just to be sure.

Join the conversation

4 of 18 comments
  • Karen
    on Jul 18, 2019

    Your Labor of Love is Absolutely Gorgeous ❣️

  • Maria Selweski
    on Aug 7, 2019

    We did not have much luck with Polymeric sand. We worked many hours; replaced all the sand. We followed every step. Within weeks, weeds started popping up. Now we have a ton more weeds than before.

Your comment...