How do you get the old plywood back off of a corner hutch to replace it? Someone cut a hole in the back of it and the bottom of both pieces of plywood are also damaged and they need to be replaced.
If you could gently wedge a very very thin pry bar that should give you enough room to slowly and very gently remove that.
If all else fails could you just cover over the old plywood? If it was painted it would blend right in. Even if it was sanded and stained again that would also help this spot to blend in.
The easiest way to take it off is to use a mallet and gently tap the back piece from the inside of the cabinet. It is probably held on by small nails. If you are careful enough, you’ll be able to use the piece for your measurements for replacement piece.
If the hutch is going to stay where it is, fill the holes and then wallpaper with a textured paper and paint or apply self stick wood flooring panels.There are so many other coverings to consider.
Hello. Can you see the small nails on the backside? If you can you could try to pry them out with a screwdriver and or the opposing end of the hammer. Sometimes even needle nose pliers can be helpful. Alternatively you might try the approach of going on the inside of the cabinet take a block of wood and pound on it with a weighted hammer to see if you could push the nails outward and then go to the back side to see if nails have emerged and then you can pull them out
That plywood is likely structural. You may have better luck covering it with something from the front - say wallpaper or beadboard panels. You could fill the holes and paint as well.
HI Betty, you should be able to use a flat headed screwdriver and slip it in between the frame and the back to pry it up a little. Once you have it pried up, you can use a hammer to remove the nails. (hopefully it isn't glued on!)
Plywood panels are normally installed with brad nails or other fasteners. A hammer can be used to move the back away from the frame enough to get in a be able to pry it away.
Get a strong putty knife and wedge in between the ply and the wood backing. Gently tap in with a hammer a lift to expose the nail head enough to get a small claw hammer around the nail head and remove. Keep going nail by nail until you can get it all off. Use the old wood as a pattern for new ply or save for another project.
Have a tan, small-ribbed couch, I am on a lot do to back surgery. Fell asleep, forgetting I had a small bowl of chocolate brownie ice cream. Woke up this A.M. w/ a... See more
At this point we are ready to just have wrought iron with cushions. Our parrot is a rescue. We have had him two years and he is free range. Before that his previous... See more
I want to redo this sofa table with a white washed look. However, the glass on both of the shelves is missing. I don’t want to replace it with glass because of the... See more
How or where can I have a recliner repaired. A spring has fallen out. I can no longer fold the leg/foot support down. Otherwise it’s in perfect condition. It’s just a... See more
How do I repair the wicker that has come loose on this chair? I want to clean it up and paint it but I don’t know what to do with the loose pieces. I’ve tried to glue... See more
Does anyone know what type of hinges are attached to the top of this folding table? The legs fold in toward the back then the top folds down flat against the legs.
I bought a dining room table and had to store it under my shed and water dripped on it and damaged it a little is there any way to fix this problem please help thank... See more
Hello ! I’m looking for inexpensive ideas to Restore this oak hutch to match it to my rattan dining table. It does have some cracking and scratches. I’ve added... See more
I recently purchased an antique wood table that was clearly around for a long time. Every time I wipe the table down it's sticky. It has a stubborn layer of 'age'... See more
I want to do the concrete look on my bathroom vanity and carry that to my kitchen counters later. My bathroom sink? Standard whatever its made from and I know I can... See more
Posted a while back for ideas on how to clean a family MCM buffet. I am not a DIYer may I say but have started this project now!!! Used Howards Clean A finish to... See more
Hello all!as I’m sure a lot of us are, I’m addicted to the oops paint section of hardware stores! Today I picked up Valspar Bonding Primer for $2.50. I’m thinking... See more
I have inherited 2 old fashioned end tables with shelf and 4 spindles on each side that connect the 2 surfaces. The original finish is very dark and the wood is pine.... See more
Can you see staples that you can remove? I would take a screw driver and remove them and then measure the wood and have some recut to put back on.
It’s nailed on☹️
If you could gently wedge a very very thin pry bar that should give you enough room to slowly and very gently remove that.
If all else fails could you just cover over the old plywood? If it was painted it would blend right in. Even if it was sanded and stained again that would also help this spot to blend in.
I would use the hole to help pry it off. If the wood is going to be replaced anyway, you don't have to worry about damaging it.
The easiest way to take it off is to use a mallet and gently tap the back piece from the inside of the cabinet. It is probably held on by small nails. If you are careful enough, you’ll be able to use the piece for your measurements for replacement piece.
to add....keep in mind that you can see the wood and it has been finished to match the cabinet. It will be easier to finish it before nailing on.
If the hutch is going to stay where it is, fill the holes and then wallpaper with a textured paper and paint or apply self stick wood flooring panels.There are so many other coverings to consider.
They are usually just attached with small nails. You should be able to pry a knife under one pieces and pry it loose.
Hello. Can you see the small nails on the backside? If you can you could try to pry them out with a screwdriver and or the opposing end of the hammer. Sometimes even needle nose pliers can be helpful. Alternatively you might try the approach of going on the inside of the cabinet take a block of wood and pound on it with a weighted hammer to see if you could push the nails outward and then go to the back side to see if nails have emerged and then you can pull them out
Hi Betty
Here is some info for your project
https://www.youtube.com/watch?v=9TEbLgvIqmk
That plywood is likely structural. You may have better luck covering it with something from the front - say wallpaper or beadboard panels. You could fill the holes and paint as well.
HI Betty, you should be able to use a flat headed screwdriver and slip it in between the frame and the back to pry it up a little. Once you have it pried up, you can use a hammer to remove the nails. (hopefully it isn't glued on!)
Plywood panels are normally installed with brad nails or other fasteners. A hammer can be used to move the back away from the frame enough to get in a be able to pry it away.
How is it attached?
Could you just fill with wood fill sand and paint them
It's nailed, stapled, or crown stapled on the back. Use a screwdriver and pliers to remove them.
It appears to be integral to the piece’s structure.
I would veneer over the holes.
It appears to be pine and you won’t find pine veneer.
If the costs of veneer shock you, then evaluate buying 1/4” plywood “project panels” - less than a full sheet.
it all depends how it is attached. but why take it off ? Refinsih whole piece .. it will be for sure safer
Get a strong putty knife and wedge in between the ply and the wood backing. Gently tap in with a hammer a lift to expose the nail head enough to get a small claw hammer around the nail head and remove. Keep going nail by nail until you can get it all off. Use the old wood as a pattern for new ply or save for another project.