How to Build a DIY Farmhouse Entryway Console Table

10 Materials
$40
5 Hours
Medium

If you have a bare wall in your entryway, a console table could be exactly what you are searching for. When visiting my sister in Iowa, she had a similar situation where her entryway had no furniture with a bare wall. After staying there for a few days, I’ve built her a DIY farmhouse entryway console table for her newly built house.


If you want to see additional picture see my website, TheDIYPlan.

Dimensions

Cut List

Step 1 – Cut Tabletop Boards

Take 2×4 and cut four pieces to 48″ in length using a miter saw. Then drill pocket holes in three of the 2x4s as shown in the picture. When drilling pocket holes the Kreg Jig should be set up for 2 1/2″ pocket hole screws, since we’re using 2x4s. These 48″ long boards will be used for the tabletop.

Step 2 – Attach Tabletop Boards

To prevent the boards from shifting when screwing in the pocket hole screws, use pipe clamps to hold the boards together. First, apply wood glue between the boards and then clamp them. Use 2 1/2″ pocket hole screws to attach the boards.  

Step 3 – Cut Legs for the Entryway Table

Next, take 2×4 and cut four pieces to 36″ in length. These boards will be used for entryway table legs. Then drill two pocket holes on one end of each leg. The pocket holes should be drilled for 2 1/2″ pocket hole screws. 

Step 4 – Connect the Legs to the Tabletop

The legs need to be attached 1″ away from the edge of the tabletop. So on the bottom of the tabletop measure and mark 1″ from all four edges. Attach the legs to the tabletop on four corners at 1″ mark using 2 1/2″ pocket hole screws and wood glue. Make sure that the legs are perfectly squared to the tabletop. This will make the leg support installation easier. 

Step 5 – Cut Leg Supports for the Farmhouse Entryway Table

Take 2×4 and cut two pieces to 39″ in length and two pieces to 9″ in length using a miter saw. Then with a table saw rip these boards in half, so you’ll end up with four 39″ long pieces and four 9″ long pieces. If you do not have a table saw, you could use 2×2 boards instead. Drill two pocket holes at each end of the board. These leg support boards will be used to connect the legs together. 

Step 6 – Connect the Upper Leg Supports

Place the 39″ boards and 9″ boards between the legs as shown in the picture. Secure these boards to the legs using 2 1/2″ pocket holes screws. You could also use a few screws to attach these leg supports directly to the tabletop.

Step 7 – Attach the Lower Leg Supports

The lower leg supports need to be installed 1 1/2″ from the floor. You could always adjust this measurement higher or lower to your preference. Measure and mark 1 1/2″ from the bottom of each leg. Then attach the 39″ boards and 9″ board to the legs using 2 1/2″ pocket hole screws.  

Step 8 – Cut Boards for the Bottom Shelf

For the bottom shelf, take 1×8 board and cut seven pieces to 12″ in length. The two pieces on the left and right side of the table will have a notch to wrap around the legs, see picture. Using a table saw cut out 3 1/2″ x 1 1/2″ notch on both sides of the board. Next, the middle board will need to be trimmed to 2 1/2″ in width. Your measurement might be slightly different, so make sure to measure the space between the boards before making the cut. 

Step 9 – Nail Shelf Boards to Lower Leg Supports

Now place 1×8 boards on the lower leg support boards inside the table and attach them with nail gun using 1 1/4″ brad nails. 

Step 10 – Make the Cross on Ends of the Table

To make a cross at the ends of the table, take 2×4 and cut two pieces to 33″ in length. These boards will be cut shorter later on. Then with a table saw, rip both of the boards in half, so you’ll have four 33″ long pieces. 

Take one of the boards and hold it against the side of the table diagonally at the location where it will be installed. Then on the backside of the board draw a line on top and bottom marking where to cut it. The total length of the board should be around 31 5/8″ with 13-degree miter cuts on both ends. The second board for the cross should be an exact mirror of the first one. 

Once both boards are cut to the right length, insert the boards at its correct location and draw the lines on the backside for the lap joint. Use a miter saw with a blade stopper that will cut a notch 7/8″ deep. The blade stopper allows you to stop at a certain height. Rotate the blade to match the angle of the lap joint. Slide the blade thru the notch area and make multiple cuts. Use a wood chisel to remove wood pieces from the notch. Repeat the process for the second cross. 

Step 11 – Join and Install the Cross on Both Sides of the Table

Apply wood glue inside the lap joint and join the board together creating a cross. Insert the cross inside the table between the legs and attach it to the legs using a nail gun with 2″ brad nails. 

Step 12 – Sand and Stain the Table

Before staining the table use a random orbital sander with 220 sand disk and sand the entire table. Also, sand the edges of the table to make the corners slightly rounded. 

When applying stain, make sure to apply pre-stain first to prevent blotching, especially if you’re using pinewood. Then apply stain and wipe it off with a clean cloth. After the stain dries, apply a coat of matte polyurethane. You’re done with a DIY farmhouse entryway console table.

Any price and availability information displayed on [relevant Amazon Site(s), as applicable] at the time of purchase will apply to the purchase of this product.
Hometalk may collect a small share of sales from the links on this page. More info

Top Hometalk Projects

15 Amazing Craft Projects That You Can Do Under 15 Minutes
30 Fun Ways To Keep Your Home Organized
29 Ways To Get A Splash Of Blue In Your House
The Easiest Ways to Grow a Bumper Crop of Tomatoes
25 Beautiful Things You Can Make With Rope & Twine
14 DIY Must-Haves For All Camping Trips
16 Stunning Sign Ideas You Can Make for Your Home
30 Adorable DIY Ideas For July 4th
25 Christmas Wreath Ideas You Don't Want To Miss This Year
25 Adorable Ornament Ideas to Get You SUPER Excited for Christmas
30 Essential Hacks For Cleaning Around Your Home
32 Space-Saving Storage Ideas That'll Keep Your Home Organized
15 Easy & Colorful DIY Projects For Your Home
31 Gorgeous Homemade Candle Ideas You're Going to Want to Try
25 Decor Ideas That Will Add Some Spring to Your Home
TheDIYPlan

Want more details about this and other DIY projects? Check out my blog post!

Go

Have a question about this project?

Join the conversation

3 of 7 comments
  • Jim Cox
    on Sep 9, 2020

    Fantastic work, great pics too


  • Em
    on Sep 11, 2020

    Love the project, the look, and I'm pretty sure I'd love a brother just like you. I'm 73, but if you'd like to adopt a sister, I could be persuaded. lol Your sister is a lucky girl.

Your comment...