How to Make and Install a DIY Wooden Towel Bar

9 Materials
$5
2 Hours
Easy

If you have kids and your bathroom towel bar was ripped off the wall, you can make your own that should last a long time. Below is a tutorial on how to repair a drywall hole and make a new DIY wooden towel bar for the bathroom.


For more information pictures visit my website at TheDIYPlan.

Step 1 – Cut the Boards for the DIY Wooden Towel Bar

Take 1×4 board and using a miter saw cut two board to 26″ in length and two pieces to 1 1/2″. Then sand the boards using a random orbital sander. 

Step 2 – Assemble the Boards

Attach the side pieces to the backside with wood glue and 1 1/4″ brad nails using a nail gun. Then attach the front side. Try not to use a lot of wood glue so that it does not come out from the sides. It’s harder to clean the excessive wood glue once the towel bar is assembled. 

Step 3 – Stain the Boards

Brush off the sawdust and apply a coat of pre-stain to prevent stain blotching. Then with a brush apply a coat of Espresso stain and wipe it off with a shop paper towel. 

Step 4 – Remove the Old Towel Bar From the Wall

To remove the old towel bar, usually there’s a set screw at the bottom of the bar that needs to be unscrewed. Once the screws are removed on both ends, lift up the bar and take it off from the anchor clip that’s attached to the wall. If the towel bar was ripped off from the wall then you don’t have to worry about unscrewing the drywall anchor. Otherwise, unscrew both the anchor clip and the drywall anchor that holds the screw.  

Step 5 – Patch the Hole with a Drywall Mesh Tape

Usually, when the towel bar is ripped out from the wall, the drywall anchor pulls out a chunk of drywall and makes the drywall bulge out around the hole. Take the backside of the screwdriver then push back the bulged out drywall. Sometimes when pushing in the drywall it makes a hole larger, and that is fine as long as you don’t have a bump in the drywall, which will be visible once you paint over it.

Step 6 – Apply Drywall Mud Over the Mesh Tape
Step 7 – Spray Texture and Paint
Step 8 – Find the Studs

Use a stud finder to locate the studs in the wall. Mark on the wall and then transfer these marks to the towel bar. You want to make these marks with a pencil so that you could erase them later. Also, draw two horizontal marks using a level to make sure the towel bar you’re attaching is perfectly leveled. You don’t want the bar to be cockeyed. 

Step 9 – Pre-Drill the Holes for Screws and Attach to Wall
Any price and availability information displayed on [relevant Amazon Site(s), as applicable] at the time of purchase will apply to the purchase of this product.
Hometalk may collect a small share of sales from the links on this page. More info

Top Hometalk Projects

30 Neat Ideas To Upgrade Your Backyard
30 Different Ways to DIY an Adorable Snowman This Winter
15 Amazing Things You Can Do With Paint Stirrers
Transform Tuna Cans Into Gorgeous Lighting In 10 Simple Steps
Live Life In Color With These Amazing Ideas For Your Home
Do You Want to Make Over a Room in Your Home & Add Gorgeous Built-Ins?
15 Easy & Colorful DIY Projects For Your Home
TheDIYPlan

Want more details about this and other DIY projects? Check out my blog post!

Go

Have a question about this project?

Join the conversation

2 of 11 comments
  • Carolina
    Carolina
    on Oct 9, 2020

    Hey!! I like this. I might just do this and get rid of those nasty, flimsy towel hangers.

  • RC Leach
    RC Leach
    on Oct 16, 2020

    Hi! You could also screw the back onto the wall before screwing the front onto the back, to give you a straight on angle, which would also aid in setting the screw heads flush, so they never snag on the towel. Always, pre-drill the screw holes. To determine what size drill bit to use, hold the bit in front of the screw. If you can see the thread on both sides of the bit, but the body of the screw is barely obscured by the bit, it is the perfect size.

Your comment...