I have to replace this board with waterproof stuff. I want to then tile the enclosure. How far should the tile go- up to where the edge of the tub is? I would think that is should go to the far edge of the tub? I mean the vertical edge of the new tile...But i may want to put in a sliding door enclosure for the tub. Would that affect how far the tile goes? I plan on rounding the edge with bullnose.
The edge of the tub where the vertical tile edge will be.
Hi Gregory: I think the tile should go as high as the tub is. The surround should sit flush on it, and the doors would then be attached to the surround.
Hi Gregory, hope this information helps you finish your project with your tub. How close to the tub should I tile?
Plan to extend the tile 2 or 3 in. beyond the tub and to leave at least a half tile along the wall if possible. Don't stop tile even with the end of the tub. This leaves the walls along the front of the tub vulnerable to water damage, and doesn't look as finished as tile extending to the floor.
You can tile the entire wall and add the doors onto the tile. My parents home is a 1950's build with tile on all 4 walls. They had sliding doors added later and it was no problem. You will just want to use a drill bit that is for tile on the installation.
You must have a shower in the tub if you plan to put a sliding door on the tub later. If that being the case, and the tub will be enclosed take it several tiles past the tub enclosure and add the tile trim. Smaller ones that finish the edge. They are very pricey though. Horizontally go the to the ceiling.
most of the time the tile (if there is no shower also in that area) goes two to three stacks up behind the tub just as an accent but you can tile the entire wall if you like that look-
does this tub have a shower in it as well? otherwise you wouldn't really need a shower door but you could do a curved shower rod and curtain there for privacy but if you want a shower door you would need to go up further to keep the dry wall from getting wet
About a foot minimum. But you don't have to have it all in a straight line, if you fancy doing something a little different. The choice is yours, Draw out something to see if it works for your overall design. Have fun!
If it were my home, and I've done this in the past, is to install the tile all the way to the ceiling on all sides except where the door enclosure is. It actually makes the bathroom appear much larger and gives a nice, clean unified look to the bathrub/shower area. I used white subway tile with my white bathtub.
Thanks, but maybe i wasn't clear...i am interested to know how far over the tub in a horizontal direction. How far the tile should go along the wall over the edge of the tub into the bathroom. Hope this is clear with the picture.
Hmm, I must not have been clear. I am interested in how far the tile goes out from the tub along the wall. - should it stop at the end of the tub, go another 4 inches etc? This would be a question if I want to install a framed glass shower enclosure.
It's up to you and how you want it to look. With just a shower curtain, you usually tile beyond the tub to protect the drywall from water damage that happens over time. If you are using a frameless unit, it might look better to extend the tile beyond the glass. If the unit has an aluminum frame sealed to wall you don't have to extend the tile. Personally I think tile over concrete board gives you the best longterm waterproofing protection. There is a risk moisture will eventually find its way behind the frame and get to the drywall.
Hi there. I tried the Homax Tough as Tile product (Bathroom, Sink, Tub & Tile Refinish) on the tiles in my bathroom shower. I waited the 3 hours as mentioned. The... See more
My 98 year old mother is staying with my sister since she has gotten out of rehab. She is very unsteady and sits on shower chair in the bathtub. She need something to... See more
We have put new tile on 3 wall of the tub all the way to the ceiling. How do I put the curved shower rod up without cracking the tile? Is there a special drill bit... See more
The 2 bottom rows of my bathroom wall tiles have a brownish appearance although it is cleaned regularly. See photo attached. Your recommendations on how to clean the... See more
The walls and the tub are all one piece and are turning a nasty yellow color, probably from our hard water. I have tried many things to get this out with no luck. ... See more
I have looked everywhere, I think, and can't find what I want. I want one of those cheap plastic covers for a shower curtain rod in brown. I want to put all my... See more
I did not do my homework on upkeep for slate shower tiles. Busy work schedules, too many bathrooms to clean, ...I got all the excuses....I will never ever put slate... See more
Your comment...
Tile Layout for Tubs and Showers
https://www.familyhandyman.com/project/tile-layout-for-tubs-and-showers/
Bathroom Wall Tile Height: How High Should You Go?https://www.fireclaytile.com/blog/full/tile-school-bathroom-wall-tile-height-how-high-should-you-go
Hi Gregory: I think the tile should go as high as the tub is. The surround should sit flush on it, and the doors would then be attached to the surround.
Here are some sites that may help:
https://www.lowes.com/n/how-to/install-tub-shower-surround
https://www.dummies.com/home-garden/home-improvement/kitchen-bath-remodeling/how-to-install-a-shower-or-tub-door/
Good luck
Hi Gregory, hope this information helps you finish your project with your tub. How close to the tub should I tile?
Plan to extend the tile 2 or 3 in. beyond the tub and to leave at least a half tile along the wall if possible. Don't stop tile even with the end of the tub. This leaves the walls along the front of the tub vulnerable to water damage, and doesn't look as finished as tile extending to the floor.
Tile Layout for Tubs and Showers (DIY) | Family Handymanwww.familyhandyman.com › ... › Fixtures › Showers
There are lots of bathroom tiling projects here that may help you also:
Home and Garden DIY Ideas | Hometalk
Extend the tile at least six inches beyond the tub. A sliding shower door can be installed over or to the tiled wall.
You can tile the entire wall and add the doors onto the tile. My parents home is a 1950's build with tile on all 4 walls. They had sliding doors added later and it was no problem. You will just want to use a drill bit that is for tile on the installation.
You must have a shower in the tub if you plan to put a sliding door on the tub later. If that being the case, and the tub will be enclosed take it several tiles past the tub enclosure and add the tile trim. Smaller ones that finish the edge. They are very pricey though. Horizontally go the to the ceiling.
most of the time the tile (if there is no shower also in that area) goes two to three stacks up behind the tub just as an accent but you can tile the entire wall if you like that look-
https://www.youtube.com/watch?v=vkJSdmmeeS0
does this tub have a shower in it as well? otherwise you wouldn't really need a shower door but you could do a curved shower rod and curtain there for privacy but if you want a shower door you would need to go up further to keep the dry wall from getting wet
https://www.houzz.com/discussions/2311932/how-far-out-beyond-tub-shower-to-tile
Should go at least one tile beyond the edge of the tub
try to imagine how high it the water will splash up and go to at least there.
Hello again,
About a foot minimum. But you don't have to have it all in a straight line, if you fancy doing something a little different. The choice is yours, Draw out something to see if it works for your overall design. Have fun!
If it were my home, and I've done this in the past, is to install the tile all the way to the ceiling on all sides except where the door enclosure is. It actually makes the bathroom appear much larger and gives a nice, clean unified look to the bathrub/shower area. I used white subway tile with my white bathtub.
Thanks, but maybe i wasn't clear...i am interested to know how far over the tub in a horizontal direction. How far the tile should go along the wall over the edge of the tub into the bathroom. Hope this is clear with the picture.
I took our tile from base of shower to the ceiling on all walls. I also installed 1/2" thick cement board to cover the studs.
Hmm, I must not have been clear. I am interested in how far the tile goes out from the tub along the wall. - should it stop at the end of the tub, go another 4 inches etc? This would be a question if I want to install a framed glass shower enclosure.
It's up to you and how you want it to look. With just a shower curtain, you usually tile beyond the tub to protect the drywall from water damage that happens over time. If you are using a frameless unit, it might look better to extend the tile beyond the glass. If the unit has an aluminum frame sealed to wall you don't have to extend the tile. Personally I think tile over concrete board gives you the best longterm waterproofing protection. There is a risk moisture will eventually find its way behind the frame and get to the drywall.
Normally you would go past the edge of the tub by a couple of inches, The glass door frame would be even with the edge of the tub.
I would go to the ceiling when tiling a tub enclosure for a shower
3 inches past the edge of the tub and to the ceiling vertically.
We always go past the tub regardless of the curtain or glass doors.
this is an idea that you can look at https://www.pinterest.com/pin/457959855864071899/
you can try this too! https://www.pinterest.com/pin/48061921150575105/