How do i wire a bathroom fan and shower light??

+16
Answered

Hi, i'm looking for some electrical advice. I have installed lots of lights anf switches, but i haven't added any new appliances or outlets to an existing room setup.

I have a bathroom that has an overhead light and vanity light on only one switch. I went to add a ceiling vent fan and a light over to the shower, preferably on seperate switches. Obviously i have to run a feed line over to those two items, but i am a little unclear as to handle the wiring to power those two items on new switches. Any advice it appreciated.

Also, any way to run the line over without tearing up the drywall?


  16 answers
  • GrandmasHouseDIY GrandmasHouseDIY on Nov 25, 2020

    The fans in my house were very simple, just like installing a light. The fan had a ground, neutral and hot wire to connect to the same wires that ran to a switch.

  • Ken Erickson Ken Erickson on Nov 25, 2020

    You will probably need to do some sheetrock work. I would run a 14/3 (red, white, black, ground) wire into attic (or space above) to the desired location, and fish wire up inside the wall where you want the switches. You can buy an "old work" double electric box. Power from line side of existing light switch can go to new box. Connect hot wire (black) from existing power to both new switches. Red wire would feed from one new switch to fan or light and the black would feed the other. White neutral would be common and ground continues to both units. Get an LED light so you never have to change it. Ensure light and fan fixtures are rated for damp area.

  • William William on Nov 25, 2020

    Make sure that the light circuit your connecting to can handle the extra load. You might need to put the fan and light on a separate circuit breaker.

  • Cheryl A Cheryl A on Nov 25, 2020

    I would call an electrician especially since you want to install it over a shower - better to be safe than sorry! You need to know if your panel can handle the extra load and also to be sure you don't have too much on one switch

  • Morgan McBride Morgan McBride on Nov 25, 2020

    I'd also hire this one out. I do a lot of DIY but this seems potentially dangerous if not at least checked by someone who knows what they are doing.

  • Seth Seth on Nov 25, 2020

    Found in the Journal of Light Construction:


    "Section E3703.4 of the 2015 IRC requires that at least one 20-amp circuit supply the bathroom's GFCI-protected outlets. And while outlets in other rooms can't be placed on this circuit, other minor equipment within the bathroom (like an exhaust fan) can be, according to the code — but only if the circuit serves just one bathroom. So a combo unit placed on the circuit may technically meet code.

    In practice, however, electricians almost always add a separate circuit matching the rating for the ventilation fan motor and demand from the unit's heat lamp (or blower) to avoid callbacks for tripping failures. A 20-amp circuit can safely deliver 80 percent of its load, or 1,920 watts, before running a risk of tripping (20 amps x 120 volts = 2,400 watts; 2,400 x .80 = 1,920). An average-sized hair dryer is typically rated at 1,000 watts, and the rating of a curling iron can be even higher; plug them in and turn both on at the same time and you've already exceeded the circuit's safe capacity without even switching on the combo unit. That's why some manufacturers specify a dedicated circuit (which doesn't require GFCI protection) for some of their combo units.

    Not only is wiring a separate circuit good practice, but section E3601.2 of the IRC specifies that branch circuits must have ampacities equal to the loads expected on the circuit. An installation must comply with all parts of the code, not just one provision."


    Remember that your home owner's insurance will probably not cover any loss for work not done to code:


  • Cynthia H Cynthia H on Nov 26, 2020

    Hi! There's much to do with venting, too. You might consider getting professional installation. I've done this with trickier projects like this, getting installation through where I buy the item. That way you have a licensed contractor who knows building codes and will guarantee their work. If you can't go that route, do some research online for best practices. Lowe's, Home Depot, Handyman, and This Old House all have tutorials. Good luck and stay safe!

  • Annie Annie on Nov 27, 2020

    Like all electrical questions I start by recommending that you get a professional to do or at least inspect your work prior to flicking the switch.

    The basic wiring will be easy if you have done switches in the past. Familiarize yourself with local electrical codes regarding bathrooms. Make sure that you are not over loading any circuit that you pull power from. As far as running the wires, it may be easy if the framing in the ceiling and walls are running the right direction, but even so you will have some drywall to remove and replace to do the job correctly as wires need to be fasten to the frame work.


  • Jeremy Hoffpauir Jeremy Hoffpauir on Nov 28, 2020

    First, I would call an electrician or handyman if you are unsure about anything. Depending on your existing wiring, you may be able to use your existing wiring along with a remote control kit like this: https://amzn.to/3lhdHsb


    Hope this Helps! Jeremy - https://do-daddy.com

  • Betsy Betsy on Nov 28, 2020

    Hi Gregory: I would most certainly get a licensed and bonded electrician to do this. If you do it and you're not an electrician and it fails, and heaven forbid your house catches fire, your insurance won't cover it. So, to be safe, get someone who knows what they're doing to do this, and THEY MUST pull the permit if one is needed, not you. Whoever pulls the permit is telling the city that they are doing the work, and if you're not qualified, don't pull the permit on anything. If the person you are having do the work says they can save you money if you pull the permit, show them the door. Don't ever pull a permit unless you are qualified. I can't stress this enough. Good luck

  • Agnes Chrzanowska Agnes Chrzanowska on Nov 30, 2020

    i would for sure contact professional about that

  • You can burn your house down and lose your insurance if you wire this improperly -- call a pro since you're expressing apprehension. I don't know that a fan with a light in a shower is the best course of action.

  • EvaUnit EvaUnit on Jun 17, 2021

    I have to admit I'm not too fond of electrical work.