overflow drain
How do I get this drain off the tub??
+26
Here is a metal overflow drain on an old porcelain tub i am refinishing. This is the overflow drain plate on the front of the tub below the faucet. (not the tub drain on the bottom of the tub) I would like to get it off the tub so i refinish the tub and put a new one on. No luck sofar. Is it built into the tub? Is there a screw in the middle? There may be, but it looks hacked off.
There should be a screw in the center. If you can't remove the screw you can drill the head out not the screw. A drill bit same diameter or close to the head diameter and slowly drill the head out. Once you remove the the drain, the screw stub should be there and it can be removed with a pair of pliers or vise grip pliers. Saturate the screw with WD40 and let it sit for a while to make removing easier.
Hello. That’s a great question. This link might offer some clues usinga tool. Talking with someone in a plumbing store or plumbing department of a big box our store might have the perfect solution. Best wishes on your restoration that is an exciting project.
https://www.instructables.com/Replacing-Bath-Tub-Drain/
Is this tub still in place in a home???
If so, here are instructions to remove the overflow drain via the pipe to the wall.
https://homeguides.sfgate.com/instructions-replace-tub-drain-overflow-21291.html
If not connected, try putting the handles of a pair of pliers into opposing holes on the drain. Use the handles as leverage to turn.
If all else fails, consider putting silicone sealant to cover all means of drainage through that side drain and then finish on top of the sealant.
https://www.houzz.com/discussions/5865980/old-bathtub-overflow-drain-no-screw-holes
Step 1 – Turn Off the Water. The first step is to make sure that all of your water sources are completely turned off. ...R.Remove the clip that holds the overflow cover plate to the plunger rod. ...
Try spraying some liquid wrench or WD-40 down the overflow drain pipe where to plunger sits. ...
Use pliers to grip the rod and attempt to lift straight up.
Hi Gregory, this should hope fully help you out,
https://www.youtube.com/watch?v=dcbm9Gui57E
Set the drain to its open position. Unscrew the knob on the top of the drain stopper to see if there is a set-screw underneath. If your drain stopper has a set-screw, use a small screwdriver or a hex key to unscrew it. Twist the entire stopper counterclockwise until it pulls free from its mounting post.
Huh? This doesn't seem to apply.
It should un screw, but I would think the threads are all rusty. Might have to break it to remove. You could try some WD40, Squirt some just behind it and let it sit overnight... Squirt several times and let sit for a while.. That might help
Hi
If you still have not solved this issue, and tub is still at home. Here is a good instruction how to fix it
https://homeguides.sfgate.com/instructions-replace-tub-drain-overflow-21291/laanius.dk
Most overflow drains have two screws or one center screw. Since you verified yours does not have a center screw....What is this tab in the photo?! Any chance it pops off and the tab is a guide where to place a flat head screwdriver. Similar to the backs of watches to replace a battery.
You can also use a hack saw if you have one. Would save the expense of buying a dremel. Have you tried using a pair of long nose pliers and sticking them in the holes a seeing if it twists off. I would try putting the tips in the holes and twist. I also would try sticking the handles of a pair of pliers in the holes and use another pair of pliers to try to see if it does twist off. Final option would be to cut it off.
Well folks, i discoverd that i am wasting my time. The cover for the overflow drain is integral part on the drain pipe behind it. It is impossible to cut off.
Anybody know some universal type cover to put over it?
Picture after drilling, bashing etc....
you need to get enamel spray paint and you will be fine
Can you contact a plumber for advice