2 Easy DIY Lampshade Makeovers You’ll Want to Try Now

Table of Contents

Supplies for DIY lampshade makeovers

• 3/4 yard fabric of your choice
• 80/12 universal sewing machine needle
• thread to match your fabric
• Iron
• Hem gauge (like the Clover Hot Hemmer)
• old lampshade
• spray glue (Like Elmer’s Craft Bond)
• 1 yard fringe trim or pompom trim
• embroidery floss in 2-3 colors
• embroidery needle
• tracing paper, ruler, and pen
• glue gun
• measuring tape
• chalk/marking pen

This type of DIY lampshade makeover will require a little bit of pattern making, but it’s super simple. Let me show you how.

Prep your lampshade

Unscrew the lampshade from the lamp.

Pull off the old lampshade cover and any trim. Most covers are affixed rather loosely and should peel away without too much trouble. If you’re working with a vintage lamp, you might need to be more careful as you peel away the old cover.

Know that you also can cover straight over your old cover if you’d rather.

If the fabric is weird or that icky pleated stuff, see if you can pull it off.

Make the pattern

Draw a vertical line on a piece of paper.

Line up your lampshade with the line, making a mark at the top and bottom of the shade.

Now for the fun part.

Roll the lampshade on the paper, tracing along the bottom edge of the lampshade as you go until you get back to the seam. Mark a point at the seam on the bottom and top of the lampshade and connect them to make a second vertical line.

Repeat the rolling and tracing for the top of the lampshade.

Use a ruler to add 1/2″ to the top and bottom and 1″ to one side for hems.

Cut your fabric

Cut out the lampshade from your choice of fabric using the pattern.

Press up the hems

Press up 1/2″ on the top, bottom and one side of your fabric. You’ll overlap the raw edges on the second side, so don’t worry about that.

Hem your cover

Stitch 1/8″ from the edge with a simple straight stitch around the top, bottom and pressed side.

Press the stitched edges.

Cover the lamp

Word of warning here: work outside for this part.

Spray glue has strong fumes and it definitely is not good to breathe that junk in.

Find the vertical seam on your lampshade. Spray a small amount of spray glue on the line.

Press your cover over the area you just sprayed starting at the unhemmed edge.

Continue to add a little glue, then press on the fabric all the way around the lampshade.

When you get to where you started, spray a little on the wrong side of the hemmed side and overlap the fabric.

Let the glue dry for about 10 minutes.

Add the trim

To add some interest to your fringe trim, thread up an embroidery needle with embroidery floss.

Weave the floss in and out of the trim in the open space of the trim, moving your needle in and out. Add 2-3 more rows in different colors.

If you like, zigzag on some mini pompom trim on the top of the fringe trim.

When you like the look of your trim, heat up your glue gun.

Add a 1″ line of hot glue on the bottom of the shade. Press on your trim.

Keep adding more glue and pressing on more trim all the way around the shade. Overlap your ends to finish it off.

Tada! Now you’ve got a much more interesting lampshade.

On to the rectangular shade.

Rectangular box shade DIY lampshade makeover

A little backstory. This lamp has been through it. It came with a moss brown velvet ribbon on top it’s canvas cover. At some point, I pulled that icky stuff off and recovered it with this wasabi dot cotton. Pretty cool, but it was getting dirty and it was time for a refresh.

For this tutorial, I’m going to assume that you, like me have a cover that you can pull off and use as a pattern.

Measuring your lampshade (if you don’t have a cover you can use as a pattern)

If you don’t have a cover you can pull off, simply measure around your lampshade with a measuring tape, then add 1″.

Also measure the height of your lampshade and add 1″.

Cut out the fabric

Lay down your old cover on top of your fabric. Use chalk to measure 1″ around your piece on the top and bottom and one side. Cut on the lines.

Alternatively, if you measured the lampshade, measure out your dimensions onto the fabric. Cut on the lines.

Press the hems

From here, fold the raw edges of the fabric around the old cover and press in places.

If you measured the lampshade, press up 1″ on the top, bottom and sides.

Remove the old cover.

Hem your cover

Stitch 1/2″ from the edge with a simple straight stitch around the top, bottom, and pressed side.

Glue on the cover

Just like with the previous lampshade, attach the cover to your lampshade with spray glue. Work outside, spray a little bit, smooth on a little fabric and so on all the way around the shade. Overlap the last bit, adding a bit more glue on the pressed edge to overlap where you started gluing.

Let the glue dry completely.

And that’s all there is to it to making these 2 easy DIY lampshade makeovers.

Want some more home decor sewing ideas? Check out these posts.

Elizabeth Farr is the writer behind the Elizabeth Made This blog where she shares helpful sewing tips, step by step sewing tutorials and videos to help you explore your creativity through sewing. She has written sewing Eguides and patterns, been a featured teacher at Rebecca Page’s Sewing Summit and Jennifer Maker’s Holiday Maker Fest and her work has appeared in Seamwork and Altered Couture magazines. She also created a line of refashioned garments for SEWN Denver. When her sewing machine isn’t humming, she’s playing and teaching violin, and hanging around a good strategic board game with her husband and 4 kids.

elizabethmadethis.com