These Industrial Lights Are SO Simple To Make!!

19 Materials
$40
4 Hours
Easy

Industrial lights are really on trend right now. I find simple is best when it comes to design and these lights couldn't be simpler. 2 blocks of wood and some cable. Here is how to make the industrial bedside lights.

Step By Step How To Video

Here is how easy they are to make!

Cut The Wood To Size

First thing I did was to cut the 18mm plywood back boards to size. I opted for 100mm wide so I cut that on my bandsaw. A table saw would be a better tool for this job but as the cut isn't crucial in anyway I used my bandsaw as it was already set up. You could cut this by hand too or perhaps ask your local DIY store to cut it for you too.

Cut To Length

I used 43mm x 43mm Walnut for my light so with the width dimension cut its time to cut the Walnut and Plywood to length. I used my mitre saw for this but you could cut this by hand too. I cut the Walnut pieces to 150mm long. I cut the plywood pieces to 180mm long.

Drill Holes For Dowels

The Walnut pieces will get attached to the Plywood back panels using dowels. I only had 6mm dowels on hand so I had to drill 2 holes per piece. Ideally I would have used just 1 10mm or 12mm dowel in the centre of the pieces.

Add Dowel Pins

To make aligning the dowels easier I use Dowel Centre Pins. These sit on the holes drilled. They can then be used to leave an imprint on mating piece. In this case they leave an imprint on the plywood back panels. I can then drill holes where the marks are and know they will line up perfectly.

They can then be used to leave an imprint on mating piece. In this case they leave an imprint on the plywood back panels.

I can then drill holes where the marks are and know they will line up perfectly.

If I were using just 1 dowel I would just mark centres on the walnut and plywood pieces. I wouldn't need to use the dowel centre pins at all then.

Now the wooden dowels can be glued in place.

Prep The Walnut

While the glue was drying on the dowels I used my router to add a 45 degree chamfer to the edges of the walnut. I could then drill a 8mm hole in the front and back of the walnut piece. This will be where the light cable gets threaded through later.

Glue Together

The piece can be joined together now using the dowels and wood glue. A couple of clamps hold them in place while the wood glue dries.

Paint & Add Finish

I wanted the back panels to look like metal so I sprayed them with hammered effect black paint. In hindsight I would have done this before gluing on the walnut but the painters tape did a good job at preventing overspray. Once the paint was dry I gave the lights 3 coats of spray lacquer, sanding between each coat.

Add Hanging Hardware

To hang the lights on the wall I used keyhole hangers. These are really strong fixings and really easy to install. They can be mounted just with screws but I prefer to route a small pocket for them to sit flush in the back. I use the router and a straight bit to do this. They can then sit in the pocket and get secured in place with a couple of screws.

Wire Up The Lamps

Now the wire can be threaded through the front hole. I added some painters tape to stop the cable sleeve from sliding back. I wrapped the cable around the walnut piece and then threaded the rest of the cable through the back hole.

As you can see I also wired the lamp holder onto the front cable. This is really easy to do but I'm not an electrician so please do this at your own risk. Always consult an expert when it comes to electricity.

I then wired a plug on the other end of the cable. Again, consult an electrician if unsure about how to do this.

Hang On Wall

The keyhole hangers simply slide onto a single screw in the wall. When pushed down into place they offer a lot of strength. All that's left to do is plug them in and switch them on. I used Philips Hue bulbs so I can control them wirelessly too.

Done!

I really hope you like this project and give it a go for yourself. They're really simple to make and can be modified to suite your style and décor easily.


Resources for this project:

See all materials
Any price and availability information displayed on [relevant Amazon Site(s), as applicable] at the time of purchase will apply to the purchase of this product.
Hometalk may collect a small share of sales from the links on this page.More info

Average Joe's Joinery
Want more details about this and other DIY projects? Check out my blog post!
Go

Frequently asked questions

Have a question about this project?

Comments

Join the conversation

 3 comments
Next