Easy DIY Pool Cue Rack

Manatee Pants
by Manatee Pants
3 Materials
$10
2 Hours
Easy

About 15 seconds after we got our pool table set up, we both looked around the room and realized something was missing. We had made sure to get everything we needed to shoot pool, right down to the chalk, but danged if we hadn’t thought about where we’d put the cues. Fortunately, the old scrap pile was just a few steps away, and about an hour and a half later, we had the stain drying on this beauty.

The red mahogany stain on the rack fits in perfectly with our purple pool table

This pool cue rack is easy and cheap to build, plus it’s simple to install with standard plastic drywall anchors. If you choose nice wood for the project, you’ll have an elegant-looking piece of furniture for your billiards room. I happened to have the cap moulding laying around, but you may not be able to find it at your local big box hardware store. Try your local lumber yard or recycled building materials store — you only need 28″ of material, so you’re likely to find it in a leftovers bin.


Pool Cue Rack: Materials



  • 1×6 whitewood board — 3′ (92 cm)
  • header cap moulding* — 28″ (71 cm)
  • 1½” (38 mm) felt furniture pads — 6
  • plastic wall anchors — 4
  • ~2″ (5 cm) wood screws — 4
  • red mahogany stain
  • semi-gloss polyurethane
  • wood glue

*I used scrap redwood header cap moulding with a 2¼” x 1½” (5.7cm x 3.8 cm) ogee profile. Substitute any moulding that you like.

The rack has enough space behind the cues for a brush, ball rack and chalk.

Tools

Jigsaw |Router and bottom-following ogee bit | Drill with standard bits and a 1½” (38 mm) spade bit | Table saw or circular saw (optional)


Construction



  1. Cut two 17″ (43 cm) long pieces from a 1×6 board for the top and bottom shelves. Using a table saw or circular saw, trim he shelves to 5″ (12.7 cm) wide (this is optional if you don’t mind a slightly wider rack). The rack will hold six cues, and you can use a whitewood board or any hardwood you prefer.
  2. Set a compass to a 2½” radius, or exactly half the board width. Draw a half circle at both ends of each shelf and then cut out the curves with a jigsaw.
Use a narrow fine-toothed jigsaw blade for best results cutting a tight curve like this
  1. Choose which board will be the top shelf and which will be the bottom — you’ll be looking at the underside of the top shelf, and the topside of the bottom shelf — and mark the center points of the cue holes. Space the holes 2½” (63 mm) apart, and 1½” (38 mm) from the front edge. The holes are closer to the front, leaving space behind the cues for your ball rack, brush and chalk.
  2. Use a 1½” (38 mm) spade bit to drill holes through the top shelf. Use the same bit on the bottom shelf to make a depression about ¼” (5 mm) deep. Note that you can’t use a hole saw for this!
Make the depression just deep enough for the furniture pads. You can wrap tape on the bit to mark the depth.
  1. With an ogee bit, rout a decorative edge on both shelves. You want to rout the edges that will be visible: the bottom side of the top shelf and the top side of the bottom shelf. Do not rout the back edge of either shelf.
Adding a routed edge provides a big payoff to the look of the cue rack
  1. Cut a notch with your jigsaw in the front of the top shelf to one of the holes. This is for your bridge. The notch needs to be slightly wider than the narrowest part of the stick. That way, the bridge will not fall out of the rack, but can be removed by lowering it until the stick fits through the gap.
The notch in the leftmost hole holds your bridge cue
  1. Now cut two 14″ (35.6 cm) pieces of the header cap moulding and glue them to the bottom of each shelf. Mark the locations for your wall mount screws on the moulding and drill pilot holes at each point. Use a 3/8″ drill bit to create a shallow hole, about ½” deep in each hole. This allows you to “hide” your screws in the moulding. If you like, you can cap these holes with wooden plugs after you mount the rack.
  2. Finish the rack. I used Minwax Red Mahogany and semi-gloss polyurethane here.
  3. Place 1½” round felt furniture pads in the depressions on the bottom shelf for the cues to rest on (check your kitchen junk drawer — you might already have them).
You can test the fit of the furniture pads, but finish the rack before final installation

Mounting the cue rack

The shelves are spaced 47″ (1.2 m) apart here — that’s as far apart as they could go and still hold the short cue. The bottom shelf needs to support about as much weight as a light bookshelf, so hollow wall anchors rated at 50 lbs. (22.7 kg) should be sufficient. (If you’ve got rugrats who’re liable to be rougher on the rack, then upgrade to sturdier anchors). Also, make sure to use wood screws that are long enough — they’ll need to go through the header cap moulding and deep enough in to the wall for a good hold. 2″ (5 cm) screws should do the trick.

Now, stop staring at the beautiful cue rack you just made and go shoot some pool!


Visit us at manateepants.com for more cool projects to make the world you want to live in.

Suggested materials:
  • 1x6 whitewood board (about 3 ft. or 1 m)   (scrap)
  • Header cap moulding (28" or 71 cm)   (scrap)
  • 1½" (38 mm) felt furniture pads   (Amazon)
Manatee Pants
Want more details about this and other DIY projects? Check out my blog post!
Go
Frequently asked questions
Have a question about this project?
Comments
Join the conversation
3 of 4 comments
Next