How to Repurpose a Piano Into a Bar/Drinks Cabinet

6 Materials
3 Months
Advanced
Bought this old belling piano for $120.00 for the sole purpose of making a Bar/drinks cabinet. But most say from the start, this project is not for the person looking for a quick project. There is a lot of work involved and took months to complete. But on the positive note the results were stunning.
Old broken belling piano
I started by removing all the large panels, which proved very easy, they were all just latched on. I removed all the keys because they were in poor shape. But will keep them to be used in another project. There are lots of ideas on the internet on how to reuse them.
I wanted to remove all the strings and harp to try and get some of the weight out of the piano to make it easier to move around. The strings were hard to remove. I tried to just cut them, but the tension on them when cut proved to be a bit dangerous. So released the tension first then cut the wires and then removing the wire was very time consuming.
The harp was bolted in, so had to release all the bolts, and then lay the piano flat on the floor to remove the harp, which was very heavy but we got it out. Hoping to use the harp as a feature in my garden.
I needed to remove all the pins, so I had a smoother surface to put a mirror along the back. I used a drill driver attachment on the drill to remove them all, which was another very time consuming task.
Next I removed all the internal bits so I had a flat surface to work with. I chose to cover the back in snake skin leather fabric to hide all the imperfections. I decided to strip down the surface next. I did not want to do to much work if I was unable to restore the main body of the piano. Which might look good in the picture, but was in poor shape.
I used paint stripper to remove all the old varnish and stain. It all had to be sanded by hand because the surface was a veneer and not a wood and had to be very careful not do damage the veneer. I repaired all the loose veneer. Once all this was complete I applied Cedar colour stain and 2 coats of varnish. (in hindsight I would use a spray lacquer as the brush did leave some lines.)
Made the wine racks next, Used 2 planks of wood 1200mm by 20cm and cut holes using a hole saw. One plank had 1 1/2inch hole and the other using a 3 1/2inch hole. Then cut the planks in half on the table saw to get the 2 halves of my wine rack to attach to the bottom section of the piano.
Repurposed Piano
I attached a mirror on the back and made 2 x upright posts so that I could add glass shelves for the glasses. I made a wine glass rack, using a scrap piece of plywood with slots routered into it to slide the wine glasses into, and attached that under the lid. And bought a sheet of marble laminate for the drinks top.
LED Lights added as a feature
I added a strip of LED lights and fitted them under the lid to add some lights as a feature. And finaly slotted all the large pieces back on to the piano, polished up the brass feet. And after months of work it was finally done, and the results were stunning.
To see more photos of the complete project visit. www.uniquecreationsbyanita.comTo see more projects How to make Epoxy Resin Doorknobs (Steampunk)How to repurpose an old desk into a Sandpit
Suggested materials:
  • Broken Piano   (For sale site)
  • Mirror   (Hardware store)
  • Marble Laminate   (Hardware store)
See all materials
Unique Creations By Anita
Want more details about this and other DIY projects? Check out my blog post!
Go
Frequently asked questions
Have a question about this project?
3 of 8 questions
  • Sofie Emilie Hornslet Sofie Emilie Hornslet on Nov 17, 2018

    How did you remove the harp after loosening the bolts? Did you take it out from the bottom of the piano?

  • Dan Stecich Dan Stecich on Jan 08, 2019

    How did you remove the very top lid? I am stumped, as I see now screws or attachments. Thanks

  • Frankie crain-ruf Frankie crain-ruf on Jun 27, 2020

    What did you do with the front panel from the top? Could it be remade into opening doors to enclose the top cabinet? (curious for my own potential project)

Comments
Join the conversation
4 of 99 comments
Next