Ignoring The Ceiling!? Statement Ceiling Focal Point in an Afternoon!

OnTheFly...DIY
by OnTheFly...DIY
16 Materials
$65
4 Hours
Easy
Ceilings typically get the short end of the design deal but this year, statement ceilings are trending! Creating a bold, eye-catching look above you might be 'in' but it can also quickly overpower a room. Instead of transforming the entire ceiling, construct a statement ceiling focal point. You'll still get that trending look but it won't become overwhelming or feel heavy.
You'll need:
* Trim and four rosettes
* Peel and stick wallpaper and scissors
* Spray paint, measuring tape, a straight edge, white caulk and a caulk gun, construction adhesive, and a pencil
*  Wood filler, a drop cloth,  and a paper plate
* A miter saw and a nail gun


First, pick your spot.  I've chosen to create my statement ceiling around an existing light fixture in my dining room.  You can also go with a fixture-less spot over a sitting area, alcove, or entryway.  The sky...er, ceiling's the limit!


Using the light as the middle, measure out to make a square.  I'm measuring out 48" on each side to create a 4 foot by 4 foot square.  Mark each side with a pencil.
Cut the peel and stick wallpaper to the same size as your 4 foot by 4 foot square.  More than likely, your wallpaper will be about 20 inches wide so you will need two full 20 inch pieces that are 48 inches long as well as a third piece only 8 inches wide by 48 inch long piece.  Make sure you cut the pieces so that the patterns line up.
Begin affixing the wallpaper to your square by using the pencil marks as a guide.  With a 4' square area, I was able to place one full piece of 20 inch wide wallpaper without having to adjust because of the light.


Loosen the fixture's canopy so that you can stick the next piece of wall paper behind it.  You can either turn off the electricity to this light or be really careful not to touch any wires as you work around the fixture.  Measure from one end to determine where to cut away the portion of the wall paper so the electrical box isn't covered.  
Finish affixing the remaining wallpaper and smooth out.


Spray paint the rosettes and trim and let them dry according to the directions.  I'm using Rust-Oleum's 2X Ultra Cover Paint and Primer in gloss white as this will match my finished trim in the rest of my house.
Paint the rosettes and trim and let them dry according to the directions.
Once fully dry, flip over the rosettes and add a dab of construction adhesive to the backs of each.
Firmly press onto each corner of the wallpaper square.  Overlap the wallpaper just a bit but evenly so that you have the same amount of overlap on each side.  
Shoot a nail or two into each rosette to keep it in place until the adhesive dries.
Measure between each rosette and cut the trim to fit.  
Run a bead of adhesive on the back of each piece before pressing into the ceiling and follow with a couple of nails from the nail gun.
Use wood filler or white caulk to fill in the nail holes.  I prefer the wood filler as it fills quicker and doesn't wipe away as easily.  
When the wood filler dries, spray a bit of the paint onto a paper plate and use your finger to dab the paint onto the nail holes.  I found that two coats of dabbed paint made the filled nail holes disappear.
Caulk the lines between the rosettes and trim.  This will give everything a seamless, professional finish.  Wipe up any excess caulk with a damp cloth as you go.
A trending statement ceiling focal point in one afternoon!
Resources for this project:
See all materials
Any price and availability information displayed on [relevant Amazon Site(s), as applicable] at the time of purchase will apply to the purchase of this product.
Hometalk may collect a small share of sales from the links on this page.More info
Frequently asked questions
Have a question about this project?
3 of 27 questions
Comments
Join the conversation
2 of 119 comments
Next