The Most Clever Hidden TV Cabinet

7 Materials
$50
5 Hours
Easy
Today we would like to share an innovative solution to a hidden TV. Do you wish you could hide your TV? This was Stephanie’s dilemma! Her hubby, Dan brought home this large TV with his bonus and announced he wanted to hang it on the bedroom wall.She was not a happy camper, but what was she to do? She thought about it and knew if she could conceal it when not it use, she would be happy with it.
Browsing ideas on the web, she was inspired by this hidden TV cover from pottery barn (which is no longer available) and knew that we could build our own version for much less money. After much online searching she came up with an innovative slide system to conceal the TV.
Check out this little video clip of the Hidden TV Cabinet in action!
Our original plan, was that we would construct our own box that we would mount to the wall and make our own sliding mechanism to conceal the TV, but as luck would have it we found a box for this purpose at our local thrift store! It was solid, well constructed was the right size and best of all it was only $5.00 !!! icon There was no way we could even purchase the lumber for $5.00, so we snatched it up!


While the construction was solid, we had a different vision for the finish. Stephanie’s bedroom has that relaxed coastal feel and we wanted the box to have a rustic white finish.
This box only framed the TV, there was no method for concealing it. We began by removing the decorative moulding on the front. We scored the moulding with a utility knife and then pried it off with a multi painters tool. We also removed the cross bar that the TV would mount on. Stephanie’s TV was already mounted to the wall with an adjustable TV mount. We marked, and cut it with a circular saw on the backside of the box, removing that section of wood.
I’m so blessed with friends who are always on the look out for scrap wood that I could possibly use. Well, I had a stack of tongue and groove lap siding that a dear friend had brought me when a garage was being taken down. I knew that it would give Stephanie’s hidden TV box the perfect finish.We began by using the table saw and trimmed off the tongue and groove edges from each board.
Our plan was to just cover the existing box with this chippy, white lumber. We began covering the outer edges of the box. We mitered the edges of the wood, with a 45° cut. We cut 2 sides, then made sure the fit was good before we actually attached it to the hidden TV box.We applied wood glue to the back side of each board and nailed it with a pneumatic brad nailing gun.
We applied the chippy white lumber to the entire outer edge first.
Once all the sides were covered with the chippy boards, we began to cut pieces to cover the front edge. We again made mitered cuts and glued and nailed them into position.
We had no idea if the paint on this chippy wood had lead in it and we also didn’t want it to continue to flake off. We searched for a clear coat finish we could apply that would not change the look of the wood and would seal and protect it. We found polyurethane coating with a matte finish Varathane Triple Thick Polyurethane Clear Matte.
To hang this bad boy, it took many hands! We made sure it was level and secured it to the studs in 4 different places with long wood screws.
We cut a piece of 1/2" thick MDF wood to size. We measured the opening we needed to cover, plus the width of the drawer slides with a 1/4″ additional border on each side. (The drawer slides are the mechanism that will raise and lover the panel that covers the TV).


We then painted our piece of MDF with the same paint which we used on the Benjamin Moore, Hale Navy. We only painted the edges and one side, since the other side would always be facing the TV.
In order for our panel to rise high enough to allow the entire TV screen to show we needed a 28″ drawer slide. At the local hardware store we were only able to find 26″ slides. With a little research Stephanie located some on Amazon.


Separating the drawer slides, we took the one that would mount to the cabinet and marked where we were going to attach it with screws. We drilled a pilot hole and then attached the slide with screws.
On the back side of our sliding panel we marked where to attach the other sliding bar. We first located the center where the bar would attach, marked the screw placement, drilled pilot holes and attached with screws.
We are getting close to the finish line, so exciting. We placed the canvas art on the back of the board, centered it and marked it with a pencil. This would give us an idea of where to attach it with screws on the back side.


We once again, drilled pilot holes, then on the front side we could see where to line up the canvas. We attached it with 4 screws, 2 on the top, 2 on the bottom.


We now needed some sort of bar to hold up the panel when the TV was to be viewed. We came up with the idea of using this window bolt. It is attached to the inside of the hidden TV frame, one on each side with a couple of screws.


Please check out the photos of this step on our website.
We just love how this hidden TV cabinet turned out! When it is closed, it just looks like a fabulous piece of art on the wall.


Along with this tutorial, we have an additional tutorial on HOW TO RESIZE CANVAS ARTWORK. We fell in love with this seascape canvas, but the dimensions did not work with the size of our hidden TV box. If you are curious how we accomplished this, check out this post.


https://www.2thesunnyside.com/how-to-resize-a-canvas/


Resources for this project:
See all materials
Any price and availability information displayed on [relevant Amazon Site(s), as applicable] at the time of purchase will apply to the purchase of this product.
Hometalk may collect a small share of sales from the links on this page.More info
Sunny Side Design
Want more details about this and other DIY projects? Check out my blog post!
Go
Frequently asked questions
Have a question about this project?
3 of 12 questions
  • Kristen Kristen on Aug 01, 2020

    What am I missing about keeping it in place in the up position? In horizontal it can only come so far out and there is a stop when pushed back in. How do you create a stop to keep it from coming from coming down when it is pushed up vertically?

  • Kristen Kristen on Aug 01, 2020

    Just saw the window bolt part to use for keeping it up. What is a window bolt?

  • KNewton KNewton on Aug 02, 2020

    Where are the cords? Most TVs are connected to WiFi and other devices like game consoles.

Comments
Join the conversation
3 of 127 comments
Next