Alcohol Ink Stained Glass

OnTheFly...DIY
by OnTheFly...DIY
16 Materials
$25
1 Day
Easy
Traditional stained glass panels are gorgeous but putting them together requires a diamond bit grinder and several specialty tools. Fake the look with some quilting tape and rubbing alcohol.
You’ll need: (proceeds from the affiliate links on my blog are donated to no-kill animal shelters and rescue organizations)* Glass cleaner* Paper towels* 1/4" thick Quilter's Tape* Razor blade* Glazier Points* 91% or higher rubbing alcohol* Plyers* Three 2-oz bottles with lids* 3 permanent colored markers and one black marker* Ruler or other straightedge* Picture frame with glass* Aluminum foil* A can or two (you can get these from your pantry* Safety glasses* Level* Long multipurpose lighter


***Please don’t use a small standard lighter for this project.


First, take the three colored markers apart with plyers and remove the inner ink.


Use the razor blade to slice the protective outer plastic so the inside is exposed.


Place the marker ink in a plastic bottle then fill it about 3 quarters full with the rubbing alcohol. I’m making only three colors for this project as I found that more than three didn’t give me the impact I was going for and just mixed together.


Allow the inks to sit for a day and soak.



Next, remove the glass from the frame and clean it off. Bailey’s version of “clean” leaves streaks so I’m using glass cleaner and paper towels.


Draw a pattern on one side of the glass with the black marker and ruler. I’m creating a geometric pattern with only straight lines as this will be much easier to construct with the tape.


On the other side, go over your marker lines with the quilter's tape. These will be your faux lead lines. Press the tape down very firmly with your fingers once you have it in place. You don’t want any ink to bleed underneath.


Once you have all of your 'lead lines' covered with quilter's tape, flip the glass back over and remove all of the marker with the glass cleaner.



Find a fire safe setting – an open spot outdoors or inside a large fireplace – please use common sense here and don’t do this step on the stove or on the kitchen table. I’m just sayin'. I’m using my fireplace as my glass will fit inside.


Prep the area underneath where your glass will sit to catch any extra ink that may drip off of the sides. I’m lining the area with aluminum foil.



Prop the glass over the foil with a can or two. Use the level to ensure the glass is straight as this will keep the ink on the surface.


Once level, drip your inks all over the surface of the glass in random patterns.


With your safety glasses on and all hair, fur and filmy sleeves pulled back, stand clear and use the long lighter to ignite the surface of the glass.


I have experience in glass fusing so I was initially concerned that the glass would crack once I lit the alcohol. However, the glass doesn’t get hot enough as the alcohol burns off quickly. It will be warm to the touch but not hot…and not hot enough for the glass to break.


Allow the alcohol to burn off and the glass to cool for a bit – about 5 to 10 minutes. Then, repeat the process for a second and third time and allow the glass to fully cool. Remove the tape to reveal your faux lead lines. If any tape residue remains, use the razor blade or a glass cleaner soaked cotton swab to carefully work it off.


Avoid touching any ink areas as the cleaner will take off the color.


Return the glass to its frame and secure in place with a few glazier points on each of the four sides.


If the points are hard to push in, use a flat blade screw driver to drive them in.


Display in front of a window for a colorful, light-catching focal point!


Watch the easy-to-follow video tutorial here:


Resources for this project:
See all materials
Any price and availability information displayed on [relevant Amazon Site(s), as applicable] at the time of purchase will apply to the purchase of this product.
Hometalk may collect a small share of sales from the links on this page.More info
Frequently asked questions
Have a question about this project?
3 of 19 questions
  • Ellie Ellie on Jul 06, 2021

    Could you use sharpies and alcohol or does it need more alcohol?

  • Shawna Farmer Shawna Farmer on Jul 06, 2021

    Why did u pick Sharpies? Can it be any permanent marker?

  • MEG MEG on Sep 05, 2023

    Beautiful. Do you have to burn off the alcohol or can you just let it dry?

Comments
Join the conversation
3 of 30 comments
  • MEG MEG on Sep 05, 2023

    Beautiful.

  • Melodie Melodie on Sep 06, 2023

    Can I use this method on plexiglass? I have a back door that I would like to do. And is there a sealer so you can clean the window with out ruining your masterpiece?

    • OnTheFly...DIY OnTheFly...DIY on Sep 07, 2023

      I think plexiglass would melt :( I never put seal on mine as I didn't want to mess it up but I would definitely use a spray sealer vs a paint-on one

Next