Pendant Light From Recycled Metal Blinds

Thea
by Thea
5 Materials
$8
2 Hours
Easy

Aluminium is a fantastic material work with because it bends and cuts very easily. This pendant is lightweight, fun and easy to make. Plus you are getting rid of a very ugly blind that is languishing in some corner of your house.

Cut a couple of blind slats loose


I have been experimenting with the old blind that has been laying in the garage for quite some time. I was pleasantly surprised at how easy the aluminium is to work with. I first cut the slats loose with kitchen scissors. I just cut wherever there were strings. The slats can then be slid out and washed.

Cut into the required length


Cut the slats into the required length with normal kitchen scissors. The length depends on your design and how long your slats were to start off with. I quartered mine and since my design leans itsself towards uneven lenghts I didn't even measure.

Paint if required


I spray painted some of my slats on both sides. I first applied a base coat suitable to metal, then a Rustoleum chalk colour and lastly a matte varnish.

Make a lampshade fitting


To give structure to the shade you need something to adhere the slats to. I used a disposable foil plate that is thicker than a normal pie tin. You could also just use an old lampshade, a wire frame, or a cake tin etc. but I wanted something rectangular and lightweight because I am uncertain on how much weight a pendant should carry and wanted to play it safe. I cut the oblong plate into a rectangle with scissors.

Cut the corners


You may need to cut away some of the corners.

Create something for the slats to stick to


I folded a rim right around my rectangle and flattened it out by laying it on the table and running the back of a craft knife over it. The neater you can get this the better which is why using the lid of an existing tin would be even easier. But doing it this way is fine.

Make a hole for the globe to fit through


Using a craft knife an or scissors, make a hole in the centre of the large flat surface. Mine was literally a small cross that I folded outward. Take into consideration how the globe and shade will ultimately be balanced. I then spray-painted it white to match the slats.

Stick the slats with a glue gun


Once you have the fitting, start sticking the slats to the rim in a vertical direction using a glue gun. In the picture above you will see that I started by placing the foil fitting on the edge of the counter and then sticking the slats. Remember that the foil and slats are hot so wear gloves if need be. I varied my colours and the height at which I stuck the slats.


Once the one side is done it is much easier to stabilize the fitting and you needn't work with the slats hanging down the side of the counter. If you are doing a round shade you could lay it on a towel on your work surface to stabilize it.

Complete all 4 sides


As you can see above it gets easier to position the thing once you have done one side. Even the last two sides, although small, had enough balance due to the slats on the other sides. You can also see that the slats are all stuck at different heights.

Connect the light and hang


Put the chord through the hole and connect to power and put in a globe. I decided to bend some of the slats into different directions. This is particularly handy if some of the slats stuck skew because it makes them less obvious. This is purely an aesthetic choice. If you don't like the higgledy-piggledy look of my lamp you could always stick to straighter lines.

Resources for this project:
See all materials
Any price and availability information displayed on [relevant Amazon Site(s), as applicable] at the time of purchase will apply to the purchase of this product.
Hometalk may collect a small share of sales from the links on this page.More info
Frequently asked questions
Have a question about this project?
  3 questions
  • Linda Linda on Mar 18, 2020

    Where is the picture of your finished project???

  • Cynthia Lewis Cynthia Lewis on Mar 18, 2022

    Can this be made using the plastic blinds

  • Dawn Dawn on Mar 18, 2022

    Seems like a lot of work to make. I'm sure it'll fit into someones decor. Good imagination.

Comments
Join the conversation
4 of 24 comments
  • Happy Days Hometalker Happy Days Hometalker on Mar 18, 2022

    Very cool indeed !

    • Thea Thea on Mar 18, 2022

      Ah,I remember you. Hi! You and I seem to share the same off-beat taste.

  • JH JH on Mar 18, 2022

    Okay, you are the one who made the "covid" light. lol

    Love the originality, but not my style.

    Very creative!!

    • Thea Thea on Mar 18, 2022

      😂Lets just say I love sculptural lights.

Next