Put Together an Easy Modern Farmhouse Barn Door in Only 8 Steps

The Rehab Life
by The Rehab Life
2 Materials
$80
5 Hours
Medium


I’ve been slowly adding farmhouse touches to my home, and for a while I’d been wanting to try my hand at making my own sliding farmhouse door. Because I knew I wanted to paint it, I didn’t need to use wood for my door, and chose to work with MDF as it’s a bit lighter than plywood. This also cut down on the cost, and allowed me to make this door for only $80. Easy, quick, and cheap, what’s not to love? Let's learn how to build a barn door.


DIY Modern Farmhouse Barn Door


Tools and Materials:

  • Four 1”x4” x8ft MDF board
  • One 1”x8” x8ft MDF board
  • Two 1”x2” x8ft MDF board
  • One 4’x8’ sheet of ¾” MDF
  • Circular saw
  • Wood glue
  • 1 ¼” trim head screws
  • Drill and impact driver
  • Miter saw
  • Tape measure
  • Wood filler
  • Sanding block
  • Paint
  • Paintbrush
  • Paint roller
  • Barn door hardware
  • Protective gear
Cut the MDF Boards

Cut the MDF Boards


With all of my materials gathered, I needed to cut them to the right size for my barn door. Using the 1”x4” pieces, I cut them into three pieces that were 65 ½” long and six pieces that were 12 ¾” long. As always, measure twice, cut once. Make sure you have the proper measurements so that you don’t accidentally make the wrong cuts and have to run back to the store for more MDF board in the middle of a project. Then I took the 1”x8” board and cut it into two pieces that were each 36” long. I set the 1”x2” pieces aside for now.

Create the Backing for the Door

Create the Backing for the Door


Next, I needed to measure and mark the board. I wanted to cut it down to 36”x80”. Once I had marked where I wanted to cut with a pencil, I took my circular saw and cut the board. This sheet will serve as the backing for the door, so if you need a different size door for your space, cut it to size.

Cut the MDF Sheet


Glue the MDF Boards to the Door

Glue the MDF Boards to the Door


Taking one of the 1”x8” x36” pieces I had already cut, I applied some glue to the back of it. Make sure to apply just enough for it to stick without spurting out when you glue it on. Then I glued it flush to the short end of the MDF sheet. 

Secure

Once in place, I secured it with trim head screws. I made sure that the screws were evenly placed, but we’re going to cover them up later so don’t worry too much about a lot of screws showing through on your farmhouse barn door.

Do the Side

With the top board in place, I moved on to the side. I took one of the 1”x4” x65 ½” MDF boards and glued it flush down the side of the MDF sheet. Then I secured it with trim head screws.

Line up in the Middle

For the next step I had to find and mark the middle of my door. I measured down the side and found the center. Then I glued one of the 1”x4” x12 ¾” pieces right down the middle. As before, I secured it with trim head screws. 

Repeat

Next I found the midpoint between the piece I just glued down and the top of the door and repeated the previous process with another 1”x4” x12 ¾” piece of MDF board. 

Repeat Again

And then I did the same one last time on the bottom part of the door. 

Move on to the Other Side

With one side of the board done, I started on the other side. First I attached one of the 1”x4” x65 ½” MDF boards down the center. Make sure that it’s flush against the boards that we just attached. Then I repeated the whole process again on the second side of the board. 

Screw Together

And to finish off I attached the last 1”x8” x36” piece along the bottom of the door. 

Add Cross Braces

Add Cross Braces


Remember those two 1”x2” x8ft MDF boards we put aside at the beginning? Now we get to use them! I lay one of them across one of the squares on my newly created door. I made sure that one of the edges lined up with the corners of the square, and using a straight edge I marked where I needed to cut.

Cut the MDF Board

Then I matched up the angle of my miter saw to the lines I had marked and cut. Before making any more cuts, I checked to make sure that the piece I had cut fit snugly into the square on the door. 

Place the Cross Braces

As always, Henry needed to give it his stamp of approval before I moved on to gluing and screwing it into place.

Screw the Cross Braces in Place

I cut seven more identical pieces, one for each square on the farmhouse barn door. 

Fill in the Screw Holes

Fill in the Screw Holes


Now it was time to fill in all the screw holes I had made. Using my finger and some wood filler I applied a bit of wood filler and then smoothed it over. The color of the wood filler should be light, but it doesn’t have to match the MDF board because we’re going to paint the whole door when we’re done.

Sand

Sand


Once the wood filler had dried I lightly sanded the whole door. Make sure that nothing is poking out. It’s also important to make sure that there are no ragged edges along the door because you don’t want it snagging you as you walk through the doorway.

Paint

Paint


We’re almost done! I grabbed my paint and a paint roller and, starting with the back of the door, got to painting. I rolled on an even coat of paint. 

Paint with a Paint Roller

Once the back and sides were dry, I flipped the door and painted the front. The paint roller worked well until I got to the inner corners of the cross braces. 

Touch Up with a Paintbrush

To get into all of the nooks and crannies I used a regular paintbrush. Make sure you don’t leave any of the original color showing through. It helps to double check once the paint has dried for any areas that might need a touch up before you hang the door.

Hang

Hang


It was finally time to hang my beautiful farmhouse barn door. I followed the instructions from the barn door hardware kit I had bought online to hang it up. When doing this yourself, follow the instructions that come with the kit as each one may be a little different.

DIY Faux Barn Door

I’m simply obsessed with how the blue of the door contrasts with the beam it’s attached to. My goal was to make all my friends jealous and I think I easily achieved it! What color would you choose for your modern farmhouse barn door? Let me know in the comments below.

Resources for this project:
See all materials
Any price and availability information displayed on [relevant Amazon Site(s), as applicable] at the time of purchase will apply to the purchase of this product.
Hometalk may collect a small share of sales from the links on this page.More info
Frequently asked questions
Have a question about this project?
  2 questions
  • RichandTammy Whiteside RichandTammy Whiteside on May 03, 2020

    Love this project. From what I'm seeing, MDF is almost twice as heavy as plywood but is less than half the price of plywood. What MDF did you use that weighed less than plywood? Thanks in advance.

  • Jessie Marie Deal Jessie Marie Deal on Jun 11, 2020

    What does the other side look like? The same or just flat backed?

Comments
Join the conversation
2 of 44 comments
  • Kimberly Kimberly on May 02, 2022

    Super cool door! Love it!!!

  • Monique Monique on May 01, 2023

    Don’t get barn doors; there’s a reason they’re called “barn doors”! They belong in a barn, not a house, but have to admit that as barn doors go, this one is impressive!!

Next