DIY Garden Obelisk

7 Materials
$30
3 Hours
Medium

*Disclosure: This post is sponsored by Blue Ridge Tools.*


Recently, my husband and I were exploring a local nursery here in New Hampshire (well, I was exploring and my husband was holding my plants!). I saw these tall, unfinished wood obelisks lined up and I ran over to look at them; I’ve always wanted to add one to my garden. I almost dropped when I saw the price tag… $130! After studying how it was put together I was confident that I could make one on my own for so much less so I added it to my to-do list for Spring. An opportunity came up for me to work on a project with Blue Ridge Tools and I knew exactly what I was going to build! I hope after you see how my obelisk turned out and how easy it was to build that I give you the confidence to try it on your own.

CUT WOOD TO SIZE


SUPPLIES FOR THE OBELISK:
















  • 4- 2"x2"x8' lumber
  • 4- 1"x2"x8' lumber
  • 2 inch deck/ outdoor screws
  • Stain or Paint
  • Blue Ridge Cordless Drill
  • Blue Ridge Detail Sander/Sandpaper
  • Blue Ridge Measuring Tape



I decided that I wanted my obelisk to be 7 ft. tall. I cut 12 inches off the bottom of the thicker 2x2x8 pieces of wood that will make the frame. (Most home improvement stores will do this for you at no cost.)


The 1x1x8 foot pieces of wood will make the horizontal slats of the obelisk. There will be 4 slats on each side. You will need to cut 4 pieces to each of the following sizes: 8, 14, 21, and 27 inches.

BUILD THE FRAME


Place 2 of your 7 ft. pieces of wood on a flat surface and touch the tops to make a teepee shape. Measure up 12 inches from the base of your frame and mark this spot with a pencil on both legs. This is the spot for your first board, the 27 inch size. Adjust the legs accordingly so the board runs to the end on both sides.

I spaced the boards out 16 inches apart: I marked the spot for each board with a pencil mark to make sure I kept them straight while drilling. This is what your frame should look like.

SECURE THE BOARDS


Using my Blue Ridge Cordless Drill I secured each board into place with a screw on each end of the board. The drill was so easy to use and not as heavy or bulky as most drills I have used in the past; it fit in my hand perfectly. I’m using screws that don’t require pre-drilling so I didn’t need to drill pilot holes first to prevent the wood from splitting.

REPEAT STEPS


Repeat the steps to make a second frame.

ADDING THE SIDE SLATS


Now that I had the two main parts of the frame completed it was time to add the side slats. This part would have been a little easier with two people but it was early in the morning and really, who has time to wait for teenage boys to wake up!


I used a pole and a step stool to brace the frame. The side pieces will go on quickly; you just need to use the already finished frame pieces as a guide for where to place the side slats. Again, use one 2” screw on each end of the board. Flip the obelisk over and repeat on the other side.

All built!

SANDING


Now it was time for a quick sanding. Using my Blue Ridge Detail Sander I went over the rough spots on the wood. This was a great little sander to get into all the corners and crevices.

PAINT OR STAIN


I had originally planned on staining ( I had even bought the stain!) but decided that I wanted it to be painted white. I did two coats of an indoor/outdoor semi-gloss latex.

READY FOR THE GARDEN!


I couldn’t be more pleased with how this turned out! It’s going to be the centerpiece of my vegetable garden. You can read how I transformed this area from a yard to a lovely garden here.

*Thank you again to Blue RIdge Tools for sponsoring this post; all opinions about their products are my own.*

Resources for this project:
See all materials
Any price and availability information displayed on [relevant Amazon Site(s), as applicable] at the time of purchase will apply to the purchase of this product.
Hometalk may collect a small share of sales from the links on this page.More info
Jennifer Howard| Cottage On Bunker Hill
Want more details about this and other DIY projects? Check out my blog post!
Go
Frequently asked questions
Have a question about this project?
  2 questions
Comments
Join the conversation
4 of 20 comments
Next