Fabric Draped Cement Flower Pot -with Video

6 Materials
$5
3 Hours
Easy

How To Make A Cement Fabric Flower Pot With Cloth

Have you needed a larger planter? With gardening season here, I thought making this fabric draped flower pot would fit the mold- so to speak. 🙂 I really wanted one that emphasizes curves, so I decided to add the balloons. Plus the balloons give the flower pot more girth. You can totally skip the balloons all together and it will reduce the amount of time it takes in half. This is another fun cement crafts project.

When I finished, and realized this is supposed to be a flower pot, I kinda panicked. Flowers? I know practically nothing about flowers- what do I put in here? It’s taken me a while just to start figuring out succulents. I think these look nice though!

Cloth Draped Cement Flower Pot Video

CREATE DRAINAGE HOLES FOR THE PLANTER


**If you love cement crafts projects then you may want to check out  my article on how tested 6 different types of concrete and cement mixes. There, you can also grab my Free Pocket Guide to Cement and Concrete Mixes.** icon


Cut a piece of straw into 3 pieces, each at about ½”. Using a hot glue gun, glue them in 3 places on the bottom of the bucket. I recommend adding glue to the open end to seal it to keep the cement from entering.

You want to make sure that you know which direction to place this piece of fabric because you need the holes to line up with the straws. So take a piece of fabric and cut it to about 7×10” and drape it over the glued straws.


Using a Sharpie marker, mark the 3 locations for the drainage. Before pulling the fabric off, be mindful of which mark goes where. I marked mine with a B for back, R for right and L for left.

Now twist the marked spot slightly and snip across it. This will create a circular hole. Repeat for the other 2 marked locations.

CUT THE FABRIC


** For another large concrete planter project, check out my very unique planter box, made with 3D cement tiles! **icon


Cut your material into wide strips to make it easier to dip and apply. My strips were about 20” long by 7″ wide. Assuming you are using this same 9″ high bucket for your cement fabric flower pot mold, I recommend cutting each piece to about 16″ long instead.


I wanted mine to have no rim it all so I didn’t let the length extend past the bottom of the balloon. If you want a rim, then make yours longer.

It will also be easier for you to drape the pieces if you taper one end so that it fits nicely between the straws.

INFLATE THE BALLOONS FOR THE CEMENT FABRIC FLOWER POT


Using the balloon pump, inflate the balloons. For a 9 ½” wide bucket, I used 17 balloons. Make sure your balloons will be positioned so that the tops (which will be the bottom of the planter) are shorter than the straws- the straws should protrude above the balloons and all the fabric.


Sizing the balloons will be the trickiest part because you want to have them all close to the same height. The easiest way to do this is to inflate a balloon so that it is longer than you need. Carefully squeeze the end you will be tying so that you have enough slack that you will be able to tie it.


Hold it up to the bucket to size it. Gently release some air until it is the length you want. Now go ahead and tie it. Repeat this with the rest of the balloons, using your original balloon for sizing. 

ADHERE BALLOONS TO THE MOLD


Using the spray adhesive, spray the outside of the bucket- be sure to follow the instructions on the can. The can instructions say to wait a few minutes before adhering the balloons to the bucket, but I found it easier to do this as soon as I sprayed the bucket. I did need to respray some spots a couple of times, I think because of the static from the balloons.

PREP MATERIAL AND MIX CEMENT


Take that first piece of fabric where you marked the straw locations and dip it into the bucket of water and wring it out. Set this aside again because this will be the first piece you will drape. 


Now repeat for the rest of the fabric. This should help the cement stick better. After you have done this with each piece of fabric, start mixing the cement. Mix the cement to a milkshake consistency. It should be fairly drippy.

DIP THE FABRIC & POSITION


Again, take your marked piece of fabric and dip it into the cement. Make sure it is saturated and none of the fabric is showing through. Position it in the direction and locations you marked so that it fits over the straws.


Repeat with each piece and position from the bottom of the planter, down. Take care not to cover the straw holes. When you have all the pieces positioned, if you have gaps or divots on the bottom due to avoiding the straws, then take some cement and fill in between them to make the bottom level. 


Now let this cure. Normally the cure time is 1 hour with the Cement All, but because the fabric was wet, it will take longer. Depending on air circulation and temperatures, you will need to wait 24- 30 hours.

DEMOLD THE CEMENT FABRIC FLOWER POT


First pull the straws out from the pot. If they don’t pull out easily, either try with pliers, or just take a power drill, drill from the outside and they should come right out.


Check to see if your inner mold will come out easily. If not, then pop the balloons. I used scissors to snip the ends. Once the balloons have been popped, the inner mold will come right out. 

Now it’s time to pop the balloons! I wimped out and did it the quiet way by snipping the ends, for a slow deflate. Once the balloons are out, your bucket should come out easily. 

Resources for this project:
See all materials
Any price and availability information displayed on [relevant Amazon Site(s), as applicable] at the time of purchase will apply to the purchase of this product.
Hometalk may collect a small share of sales from the links on this page.More info
Artsy Pretty Plants
Want more details about this and other DIY projects? Check out my blog post!
Go
Frequently asked questions
Have a question about this project?
Comments
Join the conversation
2 of 6 comments
  • Robyn Garner Robyn Garner on Jun 01, 2022

    Nice! As you aren't a gardener, I think you put a mandevilla vine in the pot. They grow 7-12' tall and need a trellis. I'd recommend a different plant for that terrific pot! 😎

  • Angela Angela on Jun 01, 2022

    It depends on where she’s located. I have several Mandevillas in pots all around my patio and yard. I live in the Pacific Northwest where it’s cooler and they are considered an annual here and never get too large. In a more tropical climate they are a perennial and can get quite large. I like them because they require a little care, last from May until October and deadhead themselves. And not to mention the fact that they’re gorgeous.

Next