Epoxy Over Laminate Counters

Mimzy lombardo
by Mimzy lombardo
9 Materials
$300
21 Hours
Medium

Epoxy counters are growing in popularity. Simply because awareness is increasing, in my opinion. I never heard of epoxy counters until I stumbled upon Stone Coat countertops Youtube channel. I binged all his videos because my kitchen counters desperately needed to be replaced.

I had 10 year old Ikea butcher block that didn’t match thicknesses, had a 6 inch gap at one end, weren’t supported properly and were just plain worn out. So when I stumbled upon these epoxy videos I was instantly sold. It took me a good year to research, find affordable epoxy, and gather the courage to tackle the project. So after successfully pouring epoxy in my own kitchen I quickly moved onto my next project…epoxy over formica. 

This green formica in a friends kitchen is the culprit. This kitchen previously had a floral wallpaper backsplash that we recently replaced with this tumbled marble. 

The first and one of the most important steps to an epoxy project is to protect your surrounding surfaces. Epoxy is super sticky and messy. It self levels, which means it will run to the lowest point. So you have to make sure your surfaces are level and you don’t have any cracks or crevices it can seep through. I used 7mil plastic tarps and covered all the cabinets and the entire floor of the whole kitchen. Then I used painters rosin paper from Home Depot over the top of the plastic to avoid slipping around on the plastic. The paper is very important because you will get epoxy on your shoes and you don’t want to track epoxy onto the surrounding floors. The rosin paper is particularly wise because you can lay down new layers of paper right on top of the old sticky paper to keep your area neat and clean. Double tape your tarps to the counters. I used blue painters to tape the tarps to the cabinets then I used another layer of duct tape to make sure the tarps didn’t come unstuck from the painters tape(which happened in my kitchen).

Once everything was sufficiently covered, I sanded the corners of the formica. The epoxy will pool at the corners if it can’t freely flow over the edges, so sanding the edges slightly round will allow the epoxy to flow over. Definitely a must. I also gave the entire surface a light sanding at the same time. 

The next step is to prime the formica with a really good bonding primer. I ordered mine from Stonecoat countertops. Although, I think you could probably use any brand high bonding primer. Since this was my first time with laminate, and it’s not my house, I opted to go with the Stonecoat guaranteed primer. 

While I was mixing the epoxy for five solid minutes, I had my helper/husband spray a little pool of paints into these plastic buckets. I used a separate bucket for each color and each bucket got its own paint stick for drizzling the color. 

Pour the epoxy onto the countertop scraping the bucket clean. I use a trowel to further mix the epoxy on the counter then spread the epoxy over the entire counter with either a trowel or a foam roller. Bring the epoxy to the edges last and allow the epoxy to flow over the edge. Then use a paint brush to paint over the edges to make sure you have full coverage on the edges.This is where you add the spray paint design of your choice. I like mine to look like natural stone. I don’t have any video or pictures of this part unfortunately. I’ll do a separate video on the design portion alone in the near future. 

After the epoxy is fully covering the space, use a heat gun to further level the epoxy and pop any air bubbles that may be trapped. At this point get a really close look at your epoxy to remove any stray brush bristles, hairs, lint or anything else that may have found it’s way into your epoxy. A pair of tweezers is very helpful.

I let the epoxy dry overnight before applying my second coat. You don’t have to wait overnight, but since this is not my house, I came back for the second coat the next day. If you let the epoxy set up overnight you need to lightly sand before applying the second coat. The second coat, or in some cases the third coat, really smooths out the surface and gives the marbling depth and dimension. The first coat may have some dimples and possibly some voids or holidays, and the spray paint sometimes causes a sheen difference on the surface. So the second coat of epoxy really makes all the difference.The second coat goes on just like the first coat. Pour, spread, and wipe the drips from the bottom edge. 

The countertop will be dry to the touch after 24 hours and useable at that point. However, you won’t want to set anything hot on the surface for at least 7 days. For instance a hot cup of coffee will leave a cup indention on the surface, take it from me. A full cure is approximately 30 days. 

After the counters are fully cured they’re super durable. Check out the video below...it has more detail and links to other epoxy kitchen counters.

Resources for this project:
See all materials
Any price and availability information displayed on [relevant Amazon Site(s), as applicable] at the time of purchase will apply to the purchase of this product.
Hometalk may collect a small share of sales from the links on this page.More info
Mimzy lombardo
Want more details about this and other DIY projects? Check out my blog post!
Go
Frequently asked questions
Have a question about this project?
3 of 16 questions
  • Tania Tania on Feb 19, 2021

    Can you epoxy over vinyl or contact paper ?

  • Kay Kay on Jul 01, 2022

    Tried it using the exact instructions….I had to have my counters replaced! It didn’t work for me at all…What did I do wrong?

  • Ck Ck on Aug 28, 2022

    front edge not square, can it be cut square before starting? HOW

Comments
Join the conversation
4 of 71 comments
Next