Pottery Barn Inspired DIY Christmas Snowflake

Amy Wadsworth
by Amy Wadsworth
11 Materials
$35
4 Hours
Medium

When I saw Pottery Barn's Christmas wall decor, I was captivated by their snowflake wall art made of driftwood. I instantly wondered if I could replicate the look and I knew exactly who I’d give it to once finished (my mom!). I had to create a video to show some of the techniques described below – sometimes it’s easier to show than explain. If you like the video, please give it a thumbs up and let me know what you think in the comments! You can also subscribe to my channel for a new decorating/DIY video each week.

Gather driftwood


Gather driftwood of similar thickness. Find the longest pieces to make up the three main points.

Determine longest lengths


I found that I could create 17 inch points for the snowflake. Measure, mark, and cut.

Cut angles at 22.5 degrees


Begin to line up the three main points of the snowflake. Make sure the lengths are the same even if you have to use a few pieces of driftwood to do so.

Cut 2" long inner points


Cut one end of the inner points at 22.5 degrees, and the intersecting end at 45 degrees. My driftwood pieces are about 2 inches long.

Mitre box hand saw


I used this mitre box to help me line up the correct angles. Be sure to wear a glove - after over 70 cuts you'll be feeling it. icon

Cut outer points


The outer points are also 2 inches long with the intersecting end cut at a 45 degree angle and the other end is a flat cut.

Determine the length of the plank background


I lined up my lath boards and determined how many I'd need for the plank background. Pottery Barn has an additional top and bottom plank on their design, but I kept my look more square. You can also alternate shorter boards every other one, or keep them all even. My shorter boards are 1 inch shorter than the others.

Cut and line up the plank boards


I used a ruler to make sure the shorter boards went in a half inch from the longer ones. Once it was all lined up, I used a brad nail gun to attach a vertical board to each horizontal plank board. The vertical board goes in about 2 inches from the edge.

Sand rough edges


Once both vertical boards are attached, be sure to sand off any rough spots.

Paint the planks


I used a tube of acrylic craft paint from Hobby Lobby ($2.99). It took three coats to fully cover the knots in the lath boards.

Cut and attach a square dowel


The Pottery Barn design has a square dowel under all the driftwood pieces. I made sure to buy dowels that were more narrow than my driftwood so that it would just give it a raised dimensional look without showing the dowel.


Measure each piece of driftwood, starting with the longest pieces, and cut the dowel about 1/2 inch less.

Sand the dowel pieces


My six year old daughter helped me sand the dowel pieces. It doesn't have to be perfect, but you want long slivers sanded off at least.

Attach the dowel and driftwood


I used a brad nail gun to first attach the dowel to the plank backdrop. Then I used a brad nail gun to attach the driftwood. In hindsight, I could have just glued the driftwood. I only split one piece of driftwood because I nailed into the nail in the dowel. It was by luck that it didn't happen more.

Start with the largest dowels first


Just like with the pieces of driftwood, cut and attach the longest dowels and then onto the inner points and finally the outer points.

Measure the starting point for the outer points


Use a ruler to make sure that all your outer points are starting in the same place around the snowflake.

Brad nail gun or glue


As stated before, you can glue on the driftwood to the nailed down dowel pieces. I actually love the nail hole looks in the driftwood, but it was tricky holding the round driftwood and precisely nailing it.

Measure and mark your hanging hardware


I like to add hardware low enough to a piece so that the nails on the wall don't show once it's hung.

Predrill and attach with a screw


Be sure to predrill wherever you marked the spot and then screw in the nail. Lath boards aren't hardwood and they're already thin.

Side by side


I love the clean look of Pottery Barn's planks - very smooth and thicker. And their driftwood looks conditioned or waxed. My design is more rustic and has that handmade quality, but my mom is going to love it and I love the price savings!

Use a level to hang
Done!


This wall decor will look so great in my mom's coastal decorated home for Christmas. It's neutral and should go well with all her other pieces.

Video
Resources for this project:
See all materials
Any price and availability information displayed on [relevant Amazon Site(s), as applicable] at the time of purchase will apply to the purchase of this product.
Hometalk may collect a small share of sales from the links on this page.More info
Amy Wadsworth
Want more details about this and other DIY projects? Check out my blog post!
Go
Frequently asked questions
Have a question about this project?
Comments
Join the conversation
3 of 33 comments
  • Amy Wadsworth Amy Wadsworth on Nov 21, 2021

    That's such a huge compliment! Thank you, Gwyn.

  • Gwyn Dean Gwyn Dean on Nov 20, 2022

    Where ever did you find those player piano music scores? My Aunt had a player piano many years ago when I was small child. It fascinated me so much.🙋🏻‍♀️

    • Amy Wadsworth Amy Wadsworth on Nov 20, 2022

      I found them at a vintage shop! I just thought they were so charming.

Next