How to Make a Bedside Pocket Organizer From Old Jeans

5 Materials
1 Hour

This tutorial is all about how I used the back pockets of some old jeans to make a bedside pocket organzier each for my two sons.

This is a super quick and easy project and I think looks pretty cute when it’s finished!


What I used:

  • 2 back pockets from old jeans – cut leaving at least 1/4″ around each pocket (ideally 2 or 3″)
  • Fabric strip 5″ x the width of your two pockets when sewn together
  • Length of Ribbon
  • Fabric Scraps for embellishment (optional)
  • Iron on Interfacing (heavy/firm)

A bedside pocket organzier of course needs…you guessed it….pockets.

So let’s start there.

I was cutting up multiple pairs of old jeans to make a denim quilt and I didn’t know what I would do with the rest of the jeans so I just cut out each back pocket and set them aside.

I was sensible enough to leave about 2″ all the way around the actual pocket, in some cases more, to make sure that whatever I decided to do I had enough seam allowance to sew with them!

For these two bedside pocket organizers I used two pockets each and I ended up using two matching pockets for each organizer too. What this means is I kind of made work for myself from cutting them apart….because I ended up sewing them back together!

However what I did get rid of was the thick middle seam that runs between the two pockets on the back of your jeans (see photo above). I probably could have sewn through that with my machine but it’s kind of a judgement call for you – do you want to deal with the bulky seam or would you rather not?

I also cut off the waistband for the same reason.


If you did cut your pockets out separately like I did you will need to now sew them back together (skip this step obviously if you just cut out both pockets together).

Line them up right sides together, trim edges so that the surrounding denim is the same length and sew.

Press open your seam.


Next find a strip of fabric that is the same width across as your finished pocket panel and about 5-6″ high.

I used fabric from Stuart Hillard’s Rainbow Etchings Collection.

If your fabric is directional like my yellow one was, check to make sure you have it oriented the right way and sew across the top of your pocket panel with right sides together.

Press your seam.


If you want your bedside pocket organizer to be functional you need to give it some stability. This is what the interfacing is for.

I cut out one piece for each organiser I was making. I cut it approximately 1″ smaller all the way around than my full bedside pocket organizer front panel (that’s what you sewed together in Step 3).

I used an iron on heavy weight interfacing. Follow the instructions on your particular interfacing to make sure you are applying it correctly.


This Bedside Pocket Organizer is attached to a bed by either tying it onto the bed slats (this is what I did) or the side panel of your bed (depending on it’s design).

To do this I used ribbon. I literally took the half finised organizer up to the bed I wanted to use it on and measured how long I needed my ribbon to be to tie it through the slats.

I cut 4 lengths of ribbon (2 for each side) of about 10″ each. You can make yours longer or shorter as needed.

Set these aside for a minute and we’ll come back to them.


Next you need to find a piece of backing fabric that is the same size as your finished front panel.

For my two organizers I used two pretty bland pieces from my scrap stash.

Don’t use your pretty fabric for this bit – no one will see it!

Pin your front and back panels right sides together.

Pin your ribbons inside the two panels about 2.5″ from each side. You want two sets of two ribbons. (See photos).

Sew all the way around with a 1/2″ seam and leave a 3-4″ gap for turning down one side.

Turn your (almost finished) Bedside Pocket Organizer right side out and poke the corners out with a turning tool or a chopstick.


Fold in the raw edges in your turning gap, pin, and top stitch all the way around your organizer. This will close the gap as well as finishing the whole thing off.


To finish off I found a few fun scraps of fabric and appliqued them by hand on to one of the back pockets for each organizer.

If you don’t want to hand stitch you could add some embellishment before you sew everything together – but of course don’t machine sew through the pocket as then it won’t open!


I think these look pretty cute. And they only took an hour or so to make!

Some more upcycling projects I've done for my kid's rooms that you might like are:

Resources for this project:
See all materials
Any price and availability information displayed on [relevant Amazon Site(s), as applicable] at the time of purchase will apply to the purchase of this product.
Hometalk may collect a small share of sales from the links on this page.More info
Kristen Hubert
Want more details about this and other DIY projects? Check out my blog post!
Frequently asked questions
Have a question about this project?
3 of 5 questions
  • Cathy Cathy on Aug 06, 2020

    What does the finished product look

    like ! Before & after would help to understand what you did !

  • Roberta Susan Roberta Susan on Aug 06, 2020

    Why are there no pictures of any of your DIY projects? Do we have to follow in order to see them?

  • MJ MJ on Aug 07, 2020

    Thank you for great directions of a useful item. But yes, throughout the project pictures would have been nice. Especially your finished Bed Pocket. Can you repost?

Join the conversation
3 of 16 comments
  • Liss Liss on Aug 23, 2020

  • Penny Penny on Sep 01, 2020

    I tried this myself & finished it today

    I added side rungs to it to hold my water bottles

    • Kristen Hubert Kristen Hubert on Sep 02, 2020

      Awesome! Well done you! I love your version! Thanks so much for sharing a photo too - I love seeing when people try my projects. Thanks!!