How To Make A Self Watering Concrete Planter!

15 Materials
2 Hours

Make an easy concrete DIY self watering planter for orchids, that has a self-wicking system.

So what exactly is a self watering planter?

Well, there are many different types of DIY self watering planters, but the concrete planter in this tutorial is one that is self-wicking.

The reason for having a self watering planter is maybe you aren’t the best at remembering to water your plants?

This gives the plant nice consistent access to water. Or maybe you are going on vacation? A self watering planter can solve these issues.

Now, not all plants will do well in a self watering planter.

For plants that like to dry out in between waterings- like succulents, you will want to avoid some self watering planter types.

DIY Self Watering Planter Video!

Self-wicking planters are best suited for plants like orchids and other tropicals. 

The key to making a good self wicking container is using the correct type of self-wicking cord. 

Did you know that not all plants thrive n concrete planters? The phalaenopsis orchid should be in a sealed or painted concrete planter because the concrete will may the soil too alkaline for the orchid.

*You can read all about  plant health in concrete pots here.*😄

Cut two pieces of the jumbo straw to ¼” long. 

If the inner mold container for the planter has an indent, then you will need to add the depth of the indent to this ¼” measurement (see materials notes for more details).


Fill the ends of the straws with 100% silicone caulk and let the caulk set. This should be about 1-1 ½ hours. 

Alternatively, you can fill the ends with hot glue, but they won’t remove as easily as they will with silicone.


Assuming your containers don’t have the magical perfect dimensions, to begin with, you’ll need to trim them to size.

First, take your planter mold and place it inside the outer reservoir mold. Mark the point where the containers meet in two or three locations. 

This is where you will want to trim the height of the inner and outer mold of the reservoir. 

I took a shortcut here, but it would have been better if I hadn’t because trimming these will give you cleaner lines and a better fit. 

To trim this to size, use blue tape and wrap it around the container where your lines meet, then use a utility knife to trim it. 

Next, take the insert for the reservoir and place it inside. Raise it about ¼” to allow for the bottom thickness. 

Line this up with your trimmed to size outer mold and mark the location where these meet. 

Do this in two or three points around the container, use the blue tape as a guide, and cut this to size.


For this step, I also skipped trimming the heights. 

I would have been better off trimming both of these because it made it impossible to get the top even all the way around and so I recommend trimming them to size. 

You’ll notice in my final photos that the planter is taller on one side-so if you trim the heights, you will be able to avoid this and get it even.

 Just follow the same steps as in Step 1 to trim the height of the outer mold. And for the inner mold, keep in mind it will be raised to the height of the straws you cut. 

So if the straws are ¼”, then insert the inner mold and raise it ¼” and mark this on the outer mold. 

Use the blue tape as a guide and cut with the utility knife.

You also may just want to wait until the straws have been glued to the bottom in the next step to get an exact dimension.


Once the caulk has set in the straws, go ahead and glue these to the bottom of the outer planter mold. 

Place them equally apart and spaced from the sides of the container for the best wicking placement.

First, prepare the inner molds by adding something weighted inside of them. I like to use sand.

Now apply lubricant to the outside of the inner molds for both the planter and the bottom reservoir. 

**If you love making concrete projects, then check out my Pocket Guide to Concrete Mixes! I tested 6 mixes and made a handy reference chart. It's a FREE download. 😉


The planter mold will get cast first and the reservoir will be cast after this has cured, in Step 7. 

Mix the concrete to a consistency that is like a very thick milkshake and ensure there are no lumps. 

Then pour it into the outer planter mold until it’s about ½ to ⅔ of the way full and insert the inner mold. Be sure to center it first, before inserting it.

Vibrate this until most of the air bubbles release and let the concrete planter cure for about two hours. 


With the sloped walls of my soccer pail, I was able to remove the planter just by tipping it upside down onto a soft towel. The inner mold also pulled right out. 

You may need to use a heat gun or utility knife to demold yours. 

Try to keep the outer mold intact because you are going to use it in the next step.

You will also want to keep some of the sand inside.

Remove the silicone straws either with your fingers or use pliers to pull them out.

If you have rough or uneven top edges, then sand them with a 400 and 220 grit diamond or a regular sanding sponge.


Once you have demolded the planter, make the concrete mix for the reservoir. 

This will also be mixed to a very thick milkshake consistency like the planter mold.

Pour the mix and insert the inner mold and shake and tap to vibrate. 

Now take the planter mold, with sand or something else weighted inside and place it on top of this cast reservoir to create an imprint of the container and ensure a nice fit. 

Use a small level to check that it is sitting flat.

You can remove this after the cement has set which should be about 15-20 minutes.

Let this cure about an hour


Remove the reservoir from the mold. Use a utility knife or heat gun if needed.


I wanted this planter to be a bright color to give some pop against my white orchid, and so decided to paint it. 

If you prefer to keep your self watering planter unpainted, then I recommend sealing the inside of the water reservoir so that the water doesn’t evaporate too quickly. 

Concrete is porous and the water will dry out very quickly without sealing or painting. 

I opted to both paint and seal the inside of the reservoir for extra protection from evaporation.

If painting it, then wait a day after your DIY concrete planter cures before painting it. 

Because although the cement has cured, it does still retain moisture, so wait until it is completely dry to avoid peeling paint.

To paint concrete, you can use either latex or acrylic paint. I used “oops” paint from Home Depot that I got for cheap. 

I always keep an eye on the mistake paint because you can also use this house paint for pigmenting wet cement.

Use a nylon paint brush to paint the concrete planter. You don’t need to paint it inside, plus it’s better if the pot itself is a little porous. 

Be sure to paint about an inch or two inside from the top so that the area above the soil is painted. 

To help protect the painted finish, I recommend using a concrete sealer as a topcoat. 

And for the reservoir, I recommend applying two coats of sealer to make sure most of the pores are closed. 

Wait a few hours for the paint to be completely dry, before sealing. Use a paint brush or foam brush to apply the sealant. 

**For other great concrete and cement tutorials, check out my Concrete & Cement Crafts projects. 😉


Take the self-wicking water cord and thread it through one of the holes- from the inside of the planter. 

You want to make sure the cord will be touching the roots and you also need to leave some slack inside the reservoir so that the cord can reach all the water. 

Inside the pot, a u-shape works nicely for getting a good bit of the roots.

Once you have the wicking cord length where you want it, go ahead and cut it. 

To help avoid fraying, I also recommend using a lighter to carefully burn the ends.

For now, it may be a good idea to try to leave the cord extra long. 

This is because if for some reason, the cord is absorbing more water that the plant needs, you can always tie a knot in it which will slow down water absorption.

Next, add some special orchid potting mix and insert the orchid. 

Be sure that the orchid root ball is touching the cord and then add more potting mix until the orchid sits nicely within its self watering planter.

Note: Orchid soil is typically fir bark, sphagnum peat moss and sometimes perlite.

Add fertilized soil to about ½ to ¾ full and pot your plant. Add more soil so that it comes up to about 1” from the top. 

Now just fill the reservoir and stack the orchid planter on top. My reservoir held one full cup of water. 

Don’t forget to adjust the cord by tying a knot in it, in case the orchid seems like it’s getting over watered.

**Please see my post on my website for more details on materials.

Resources for this project:
See all materials
Any price and availability information displayed on [relevant Amazon Site(s), as applicable] at the time of purchase will apply to the purchase of this product.
Hometalk may collect a small share of sales from the links on this page.More info
Artsy Pretty Plants
Want more details about this and other DIY projects? Check out my blog post!
Frequently asked questions
Have a question about this project?
  3 questions
  • Looks beautiful! You mentioned you can tint the cement with the house paint. Is there a special way/ratio to do this without changing the chemical make up of the cement or do you just pour in any amount of paint in to create the color you want? Thanks!

  • Tina Tina on Jan 19, 2021

    Aren’t Orchids ice cube only, not watered? Your projects shows it with an orchid

  • Lorraine Lorraine on Mar 05, 2021

    i’m not good with plants but what is a wicking cord?

Join the conversation
4 of 12 comments
  • Leta Leta on Jan 26, 2021

    Love this it will help me very much


  • Robin Robin on Jan 02, 2022

    I love this idea for outside container plants as well….but maybe just use the wicking cord from the bottom of the pot to a drip plastic bottom saucer like thing with some floral foam like oasis in the bottom of the pot and sides? Or maybe that would just rot…but worth a try with thirsty annuals in the sun…