Concrete & Upcycled Glass Lamps

by JackmanWorks
13 Materials

There is another studio next door to me that is a glass blowing shop. Sometimes they will throw away their scrap colored glass, so that’s how I was able to find this stuff in the dumpster. The lighting used is an RGB LED flood light. See the link below for the product I used. Both of these are able to be operated off the same remote. To form the concrete I used a wire wheel on some pine to expose the profile in the grain. The aluminum pieces are held together by brazing, it’s a sort of aluminum welding, with a installation process more similar to soldering. The plexiglass is held on with silicone caulking. 2-part masonry epoxy is used to hold the frame to the concrete (except for the top which is attached with silicone in case of maintenance). The concrete was finished with a single coat of 2-part epoxy resin. This is a summary tutorial, so be sure to watch the build video for the full experience.

Here is the build video!

This build started like a lot of my builds ... in the dumpster.

When I noticed them tossing out their scrap colored glass late last year I snagged a bunch of it knowing it could be useful. I sat on it for a long while and then created this project.

The main frame is made from aluminum angle and bar stock scraps. I use the junk blade on my table saw to cut these down to size.

I attached the aluminum pieces together using brazing. The cinder block was a perfect working surface with the heat. I heat up the aluminum pieces until they are hot enough to melt the brazing rod. You fill in the fillet until it's flush with the surface.

The base of the lamps are made from cast concrete. I used these pine planks as the casting surface as I wanted to transfer the wood grain pattern to the concrete. To bring out the wood grain, I use a wire wheel in the angle grinder, which grinds off all of the soft material.

I screw the 4 sides together and hot glue them onto a sheet of melamine. In the base casting, I made a cavity from rigid foam for the lighting to fit into. I also made it a little oversized to take some weight off the lamps.

I just used a regular concrete mix for this. Mixed it and poured into the forms. I vibrate the form to get a much air out of it as I can.

Once all that is cured, it's time to shape everything. I use a diamond grinding wheel in my angle grinder to refine the shape of the dados. I also grind off the corners to give them a little more shape.

As a finish I just used a 2-part epoxy resin. I mixed a little bit of this up to use as a thin coat because it gives it a bit of a shine and seals up the concrete. I also used the epoxy to install some rubber feet onto the bottom of the lamps. I put the concrete lids on top while the epoxy dried to keep these in place.

Once that finish dries, I mixed up some 2-part concrete epoxy to attach the aluminum frames to the concrete base. Andddd after another wait for stuff to dry, it's finally time to wire up the light. I drill a hole out for the toggle switch and for the cord on the opposite side.

I used an LED flood light for this. Dissected it by pulling the screws off the back and separating the wires from the light. The power wire goes through the switch, the neutral stays wired up to the circuit board, and the ground stays wired up to the main casing of the lamp.

I cut down some plexiglass to use to hold the glass scraps in the lamp. I made these boxes to put in the center of the lamps. It holds back the glass to cut down on weight and also allows the light to go from the base to the top of the light. To attach the plexiglass around the sides of the lamps, I put silicone caulking around the perimeter of each piece.

I put the plexiglass boxes in the center and finally get to put the glass in the lamps. Starting to look sharp! I decided to install the concrete lid to the top of the lamp with silicone caulking. This holds it in place and also allows me to remove it in case the light or anything inside ever needs maintenance.

The same remote operates both of the LED flood lights. They are RGB LEDs so they can be changed to a whole bunch of colors.

Resources for this project:
See all materials
Any price and availability information displayed on [relevant Amazon Site(s), as applicable] at the time of purchase will apply to the purchase of this product.
Hometalk may collect a small share of sales from the links on this page.More info
Want more details about this and other DIY projects? Check out my blog post!
Frequently asked questions
Have a question about this project?
  2 questions
  • Stephanie Stephanie on Aug 25, 2018

    How beautiful. Incredible job. Now, can anyone figure out how to do this like the long distance friendship lamps that are way to expensive for me??

  • Thea Thea on Apr 26, 2021

    So you made a box with the plexiglass and and simply filled the whole box with the glass? You didn’t make a 2 sided plexiglass frame that means that the centre was essentially empty?

Join the conversation
2 of 57 comments