Rustic Picture Ledges With Homemade Steel Wool and Vinegar Stain

by Rick
7 Materials
Grab Steel wool & vinegar and copy this easy DIY!

Here is EVERYTHING I'll be using to build a picture ledge by hand. It may seem like a lot but there are always substitutes if you don't have everything pictured here. Here are the essentials:

Tape Measure
Pressure Clamps
Hand saw
Wood Glue
Drill + Drill Bits
Sand Paper
Wood FiIler
Steel Wool
Distilled White Vinegar
Mason Jar

Measure out your desired picture ledge length and make a mark (mine will be 5ft or 60 inches). Carry that mark the width of the board with your utility knife. This is going to create a guide to rest the handsaw's teeth into to enable you to make a straight cut. Think of it like bowling bumpers that keep your ball from FAILING- same thing here! Clean up the ends of your cut with a sanding block.

I'll be using a Kreg Jig to join the back and bottom boards of our picture ledge. I mark out 2" from each end and 8" thereafter. Next I pre-drill on those marks using my Kreg Jig that has been setup to accommodate 3/4" material.

If you don't have a Kreg Jig you can use screws and wood glue through the back end of your back board.

Place a line of glue along the bottom board and flip it over!

After aligning the bottom board to the end of the back board, clamp the two together on each end in preparation for screwing.

Use 1-1/4" pocket screws to secure the two pieces together...forever!

Fill in all of the holes using wood filler and a putty knife.

It may take multiple coats of wood filler and sanding to get the hole nice and smooth.

Next we'll join the from 1x2 trim. Run a bead of wood glue along the front of our bottom piece...

Line the from 1x2 trim to the end of the 1x4 back board and use multiple pressure clamps to join them. If you'd like you can use a brad-nailer to reinforce the joint!

Locate your wall studs and transfer where they fall onto your ledge. Using a 1/2" drill bit, drill a pilot hole just past 1/2" deep.

Next take a drill bit slightly smaller than the shaft of the screws you'll be using to attach the ledge to the wall and pre-drill through the ledge.

We'll be using these white caps to conceal the hardware.

Grab your mason jar and tear up your steel wool. I'm putting 2 pieces of the steel wool in my one quart mason jar.

Take your distilled white vinegar and pour (4) cups into the mason jar (fill it to the top). Do not put the lid on as the chemical reaction will give off hydrogen gas and needs to breath.

Let the mixture sit 24-48 hrs.

Chemistry time!! When you combine steel wool and vinegar the solution is called iron acetate. Iron acetate reacts with the tannin in the wood, which is a naturally occurring astringent. Because pine is a softwood, it does NOT have a lot of tannin. But guess what does? Black tea!

So brew a few bags of black tea and let them steep for about an hour. Liberally apply the tea to the wood. Once absorbed into the wood, the tea (tannin) will react with the steel wool and vinegar stain give the wood a weathered look.

Pour your steel wool and vinegar mixture into a smaller container so that you can get a paintbrush into it. Paint the steel wool & vinegar stain onto the ledge. It will go on clear, but don't freak out!! After a few minutes you'll get an amazing weathered finish!

Stain the entirety of your ledge, throw some clear-coat on and attach to your wall using a level and 3-inch screws (or heavy duty wall anchors). And that's it!

For more FUN projects follow me on facebook!

Thank you for reading!

Frequently asked questions
Have a question about this project?
3 of 7 questions
  • Wei32753737 Wei32753737 on Apr 21, 2018

    Could I use this method on nearly sanded floorboards? Any problems foreseen? Thanks

  • JC JC on Nov 20, 2019

    I really like the look of the table top your showing your work on, how did you make that, if you did?

  • Gwen Patterson Gwen Patterson on Nov 20, 2019

    Must the vinegar/steel wool mixture be discarded after you've finished with it, or does the 24-48 hour waiting period provide enough chemical reaction that a lid can be placed on it then?

Join the conversation
2 of 44 comments