License Plate Journal & Desk Set

by MadeByBarb
8 Materials
2 Hours
I bet you have at least one license plate hanging around somewhere. Once you start to make gifts it becomes a habit. And it starts to become expected. So what can you get that car enthusiast guy? Yup, it’s birthday time for my ‘cars-and-everything-about-cars’ son. How appropriate is it that this license plate is from the vehicle he spent most of his childhood in… oh the memories…
This set uses 2 pairs of license plates, but you could easily make less pieces.

License Plate Desk Set
  • 4 License Plates
  • Tin Snips
  • 24" Piano/continuous hinge
  • 1/8" x 3/16" Pop Rivets & matching washers
  • Rivet Gun
  • Piece of wood (for bottom of pencil container)
  • Micro 3-ring Binder & paper and/or paper signatures sewn together
  • Hammer/Mallet
  • Pencil, ruler
  • Rotary Tool with cutoff blade or hacksaw
I love using these pop rivets to attach things. They can bring together whatever you can get a hole through and find an appropriate length of rivet. Since this needs to be secured from the back too you will need the washers that fit the rivet size. I’ve used them successfully in my  industrial felt projects and my  leather purse.

The rivet gun works by pulling the centre through and thus widening the ball end and wedging it in the washer. If you can picture that. The shaft then breaks off from the outside…
Pencil Holder
Divide the length of the plate into 4. Look at where the numbers/letters are and see if you can avoid bending the 4 corners over them. It does make a better bend if it avoids them. I had the ends come together on one side. Drill holes or hammer a large nail to make the holes large enough for the rivets. (I used 1/8″)
The 2 books or journals used hinges. Our canadian plates are 6″ tall, so a 24″ piano hinge worked well to be divided into 4. The shaft is quite thick to cut with the tin snips so I used my trusty rotary tool with cut off disc to get through it.

Then finish off by using the tin snips. Sand off any sharp and rough edges on the license plate. I like to save the finish by putting masking tape to protect it.
The spine of the books were spaced to avoid the letters on the license plate again, at about 1 1/4″ wide. Mark and cut carefully. Round off the corners a bit as well.
Plan the placement of the hinges and make holes in the license plate front and back and spine. Rivet the hinges in. The one book uses a  micro 2 ring binder mechanism. You will need disassemble it from the binder by drilling out the rivet and then riveting it in the middle of the spine. Be careful not to force it too much as the rings still need to function.
The mechanism in place and paper cut and added.

It is difficult to find the right size paper so I needed to cut it and punch the holes.

These are so rustic and full of character! You could adjust the mechanisms inside to whatever you have or come across.
Mail Holder:
The letter/mail holder is a license plate cut in half with an overlap of about 2-3″ and riveted together. Add a few felt feet to keep it from scratching the desk.

This set was a hit with the car-guy! I hope you give it a try...
Resources for this project:
See all materials
Any price and availability information displayed on [relevant Amazon Site(s), as applicable] at the time of purchase will apply to the purchase of this product.
Hometalk may collect a small share of sales from the links on this page.More info
Want more details about this and other DIY projects? Check out my blog post!
Frequently asked questions
Have a question about this project?
  1 question
  • Pamela Krugman Pamela Krugman on Jan 15, 2018
    I saved our son's first license plate. Now I know how to surprise him and put it to good use! How did you do the letter holder? Did you just bend it to that shape? Thank you!

Join the conversation
2 of 17 comments