Old Formica Cabinet to Modern Coastal
My friend‘s kitchen needed an update! After raising twin boys and what seemed like most of the entire football team, Cassy’s kitchen had seen some absuse! Since the boys and their 40 closest friends have finally gone away to college, it seemed like the perfect time to figure out what could be done. If anyone has a child in college, you are well aware... it ain’t cheap! Try having twins!! Needless to say, money was tight- a real budget didn’t exist, so we had to make the most of what we could find- spending the least possible amount. In the end, Cassy has a totally new look! Once the cabinets were done, we built a table to go with the new look. (Her old table looked just as bad as the cabinets!) You may see it in some of these pics- but I will get into the table on another post!
In this first photo You can see, these are plain (VERY PLAIN), Formica, old-school cabinets. They don’t look horrible here, but trust me... even in their best days, they weren’t very pretty!
After researching our options, it seemed the most economic and logical way to go, would be to attempt to fabricate/make trim, to reface the doors. Thankfully, we read that shaker cabinets aren’t going out of style, anytime soon and since the doors were flat, it seemed it would be fairly straight-forward. Some trim, a little sanding and painting and voila!
Well... it wasn’t that simple! Who KNEW there would be so many trim options, for what at first site, seemed like standard straight cuts!! Ultimately we chose hobby board, from Home Depot. It is lightweight, thin, but not too thin and relatively inexpensive. So we measured and picked up the boards, wood glue, paint and Brad nails. (You can do the nailing by hand, but TRUST ME... it went MUCH easier with the pneumatic nailer!!!) initially I thought we would rely primarily on the glue- by spreading it on and clamping. After one cabinet, I realized this way would be a time consuming nightmare- instead, we put very thin layers of glue on the boards and nailed them in, right away.
After a couple mistakes, (measure twice cut once!) we really started moving. I cut and attached while Cassy filled and sanded. We switched “positions” when we got tired of what we were doing. We both painted.
We tried to make the cuts as perfect as possible, but perfect wasn’t really necessary, as we filled in any gaps with joint compound and sanded smooth.
We had this entire project done in two days. Granted, we worked tirelessly day and night, but we even managed to come up with an idea to make a them a bit more modern/feminine with a coastal feel- (will get into that shortly!) keep reading!
we Knew we wanted to add a little “bling” but not too much. After all, raising twin boys, athletes... is not a job for the faint. After years of “boyish charm”, Cassy was really craving something that showed that although she had spent the last 19 years being coach, mom, dad, doctor, etc. underneath it all, she was truly a WOMAN!! We spent hours trying to find some photos of inlay- I’m typically good at research and after hours of looking, i could only find ONE photo that even resembled what we were thinking about doing. Ironically, it was a post on this site, where a woman put little tiles in the center of the doors. It was close, but still not really what we had in mind. We took a ride to floor and decor to browse around and see what we could come up with. It practically JUMPED out at us!!
EDIT: since so many are asking where to buy the sheets. I’m attempting to put a link at the bottom of this post, to amazon-
after all of the doors were put together, painted and dry, we used a dremel with carbide tip to cut the sheets to the perfect size. We glued it down with thin set. since we wanted subtle bling, we chose to only place it in the area around the stove and microwave. It was absolutely perfect! we found handles first on Amazon, using prime for next day delivery.. we thought we had a great deal. To our disappointment, the handles were awful. This ended up being the most expensive part. We returned the amazon handles and purchased solid stainless steel, from lowes.
all in all, this was a pretty simple project. With that being said, the right tools definitely made a big difference and I’m not sure I would attempt this without them. We are thrilled with this result! It was fun! In all honesty, I’m not sure i would consider going into business doing this, but seeing the transition was amazing!!
What do you think??
Resources for this project:See all materials
Any price and availability information displayed on [relevant Amazon Site(s), as applicable] at the time of purchase will apply to the purchase of this product.
Hometalk may collect a small share of sales from the links on this page.More info
Want more details about this and other DIY projects? Check out my blog post!
Published March 18th, 2018 11:14 AM
3 of 434 comments