DIY Stair Runner
Make your stairs more stylish and SAFE for kids and pets!
Hey hey, friends! I completed this stair runner project back in early February 2019, and I must say I am so impressed with how well it has held up! I knew we needed to have a stair runner for our sweet pup Napa, who I swore was going to break a leg every time the doorbell rang and she would quite literally FLY down the slippery stairs; but in that same vein, I was nervous that her nails would cause damage or frays to the carpet over time. I’m happy to report we’ve had just ONE fray so far (easily fixed with a small pair of sewing scissors and some clear nail polish to prevent further fraying), and I’m pretty sure that was from me dropping and dragging a piece of plywood on the stairs during our latest bathroom renovation. Oops!It also added a more custom look to our stairs, and y’all know I love anything that adds more texture to our home, and this did just that! The installation process was also a fairly easy – the process will be easier with two people, but I did 85% of it alone and it looks great! So what do you need and how do you do it? Let’s get started!
Step 1:First, measure how long you will need your runners to be. To do this, use the following equation: (length of one tread + length of one riser) X (total number of stairs). Add at least 15%, and purchase accordingly. I added a bit more, because the runners I chose had a design on each end that I knew I would need to cut off. So I purchased three 10′ runners, but only needed about 22 feet total, and we just BARELY made it!Step 2:Lay your runner out on your stairs and match the middle of the runner with the middle of your stairs. Use your masking tape and tape each tread on either side of where the runner will lay so that you have a guide as you’re installing. This step is immensely helpful and will keep your lines straight, especially if working with a rug with some kind of linear pattern on it, like we were!
Step 3:Cut off the very end of your runner with a pair of sharp fabric scissors. You’ll work your way from the top down. Fold the raw edge under (be sure it’s straight – you can use whatever patten is in your rug to guide you; if there is no pattern, I recommend using a level and speed square to be sure your fold is straight), line up your runner with the masking tape, and begin by stapling one staple into the very left corner, RIGHT underneath the tread, where it meets the top of the riser. The closer you get to that seam, the less you will see you’re staples. Work your way across, placing staples about 2 inches apart. Be sure the fabric is pulled taut going across, but not overly so.
It’s super hard to see the staples (and that’s what we want!), but the slight puckers in the carpet that you see right under the top of that very first tread is where the staples are. Again, the more you can wedge them into that seam where the tread and top of the riser meet, the better.I then went back in and added more staples where I thought it was necessary.
PRO TIP: You’re staples will likely be silver or brass. If your rug is black or dark like mine, you can use your Sharpie to color the tops of them before inserting them into the staple gun – this just helps hide them a bit more! Totally optional, but I thought it helped!
Step 4:Cut a piece of your carpet padding to fit your tread. Cut each piece about 1 1/2 inches less in width than your runner – this leaves a bit of space on either side of the padding so that the runner will fully cover it once installed. Also cut each piece slightly wider than your tread so that the front edge will roll over. This will help disguise the fact that there’s padding, and will give it a more finished look.As you can see, there’s about 3/4 – 1″ on either side of the rug padding, and the padding will roll over the front of the tread once the runner is laid and stapled over it.Step 5:Pull your runner down taut – more than you think you need to – you don’t want any bulges or bumps! Make sure you’re pulling it evenly as well, so that your pattern remains straight. Push your carpet padding up to the very back of your stair, and smoosh (is that a real word?) the carpet into the seam where the bottom of the riser meets the back of the next tread. Use your staple gun and first staple the left side as close into that crease as you can. Move slowly and methodically, adjusting the runner as needed, until the entire length is stapled into the seem. Add more staples as needed.Step 6:Repeat this process all the way down your stairs, stapling under the tread/at the top of the riser, and then at the bottom of the riser/back of the tread. Anytime you need to begin with a new runner rug, be sure to cut off the seam at the end of the runner you’re working with, fold it over, and end it preferably in a seam where the BOTTOM of the riser meets the BACK END of the tread. We found that the transition between rugs was better concealed this way. Then, cut off the seem of your next runner, fold it over, butt it up against the edge you just made, and begin anew!If you have straight stairs with no bends, lucky you! We have a 180 degree turn in our stairs, so I created a kind of L shape with our runners and just installed them in the way we liked them best.
Here you can kind of see how I tackled our 180 degree turn. I ended the first runner where you see above, then laid the next one straight over top of it, and centered, 90 degrees rotated from the first one. I then repeated this on the small landing below as well, which got me the full 180 degrees. I staples straight down into the landing along all of the edges you see above, but with the blackened staples, you really don’t see them at all – just be sure you're staples are FULLY inserted – no one wants to step on a staple!Step 7:Once you get to the bottom of the last riser, cut your runner, fold the edge under, and staple! And voila! You’ve just installed your very own DIY carpet stair runner!
And here's an overhead shot! We love how it turned out!What do y’all think? Is your home in need of some less slippery stairs? If so, I highly recommend this DIY carpet stair runner – and the carpet padding really makes them so much more comfy to walk on, too!Enjoy, friends, and let me know if you tackle this project – I’d love to see! You can check out more fun DIY projects on my blog - www.fiddleleafblog.com!
Enjoyed the project?
Resources for this project:
Any price and availability information displayed on [relevant Amazon Site(s), as applicable] at the time of purchase will apply to the purchase of this product.
Hometalk may collect a small share of sales from the links on this page.More info
Want more details about this and other DIY projects? Check out my blog post!
Published March 2nd, 2020 9:01 PM
Frequently asked questions
Have a question about this project?
Join the conversation
3 of 23 comments
Kim on Mar 05, 2021
Thank you Ana! Great idea for slippery stairs. Love the photo of your dog on the stairs!
Ana Ochoa - Sunrise Valley Farm Co. on Mar 05, 2021
Thank you for your kind words Kim! She’s a cutie!
Laura Szerdi on Oct 18, 2021
I think it looks great, but my OCD is kicking in at the area where you had to continue the runner at 180 degrees! lol!
Can this be used for a stair runner but over carpet?
Where did you get the carpet runner
Enjoyed your post but was baffled by the measurements you said to take. I would use the height of the riser and the depth of the tread for mine. Would that make more sense?