Chimney down drafts
-
Suffolk Concrete & Masonry on Mar 01, 2013i would have the chimney inspected professionally for structural defects. if o.k. raising the chimney 2-4 feet above the roof peak shouldnt hurt. another option might be installing a wood or pellet or gas insert with a chimney linerHelpful Reply
-
-
Betty on Mar 01, 2013What about the chimney cap will that help with the downdrafts?Helpful Reply
-
-
Woodbridge Environmental Tiptophouse.com on Mar 03, 2013A few things can cause poor draft. Chimney height, is one. Chimney location in regards to peak of roof. Chimney exposure to cold air. Undersized flue in chimney for size of stove. Missing or damaged smoke shelf in fireplace opening. The height of the chimney is the most common issue. As the interior of the flue heats up the velocity of the flue gasses increases and a greater draft is pulled up and out. This also has a lot to do with chimney exposure. If the chimney is entirely located on the outside of the house, such as one on the end of the home. The exposure of the brick or block surface is such that cold air cools down the heat within the chimney and slows this movement down. If the chimney is located near the peak of the roof, air currents can flow up the roof and create a down draft on the opposite side. If the chimney is located on the down wind side of the roof, these down drafts can pull the smoke down and into the windows, and will slow the draft down as well in the process. So a higher chimney may be needed, or perhaps a good quality chimney cap that prevents the air from blowing down the flue pipe. A undersized chimney flue can prevent enough air from going up the chimney and mimic a poor draft. While it is really not a poor draft, it simply does not have enough free air to pull the smoke up. With your issue combined smoke in windows and poor draft, I would think your issue is the chimney is not high enough and down drafts are pushing air back down the flue and down the house into the windows. Or combined with a poor smoke shelf inside. Another issue can be the size of the fireplace opening as compared to the size of the flue liner. If the ratio of the opening of the fireplace is to large for the flue the pulling effect across the front of the fireplace opening will be less then if the opening was smaller. This is why many times people install doors to make the opening smaller so more air will be pulled into the face of the fire pulling the smoke up rather then around the front top of the fireplace front. Lastly be sure before you try anything that you get the chimney examined by a professional chimney sweep. Doing something wrong can cause safety issues and burn down your home.Helpful Reply
-
-
RockfordChimneySupply on Mar 19, 2013Great points Woodbridge. There are quite a few things that can cause a poor draft. If you need any help 'troubleshooting', feel free to call us - we'd be happy to help you figure out the issue.Helpful Reply
-
-
Woodbridge Environmental Tiptophouse.com on Mar 19, 2013Here is a sample of not what to do when raising a roof on a house. In order for the owner to save a few dollars the builder did not raise the chimney when they added a third level to the house. What resulted in a chimney located way below the ridge of the roof. In the background you will see another chimney that was installed on another addition on the house that was installed to the correct height. We have instructed the owner not to use the fireplace until they have the chimney raised for safety. You can see in the other photo a PVC vent that we installed for a new high efficiency furnace. We raised this to the proper height so when they raise the chimney we do not have to come back and raise our flues again.Helpful Reply
-
-
RockfordChimneySupply on Mar 20, 2013Those are great pictures. PVC will work for venting the high efficiency furnace. But if you are venting a chimney liner and need to extend the flue, you will need a stainless steel flue extender. Below is a link if you'd like to see what one looks like: http://www.rockfordchimneysupply.com/rockford.php?item=FlueExtenderHelpful Reply
-
Related Discussions
Stop a back draft from a down draft exhaust fan on a GE stovetop
I have a GE profile gas cooktop with a down draft exhaust fan in the middle of my kitchen island. The vent pipe travels about 20 feet to the outside. However, when it... See more
Best way to make your driveway look like stone with paint?
Several years ago there was a DIY video on how to do this but can't fine it.
Which room would you pick for a room makeover in your home?
We're curious, if you could redesign any room in your home, which is the room you would choose?Whether it's your cozy living room, your bustling kitchen, or even your... See more
What are your thoughts on painted brick: yay or nay?
Painting bricks can completely transform the appearance of a home, giving it a fresh, modern look or adding a pop of color to an otherwise plain facade.On the other h... See more
How to remove popcorn ceiling that has been painted?
Does having a paint over a popcorn ceiling change how I'd remove the popcorn ceiling?
How can I get evergreen climbing vines that don't attract bees?
Need privacy screen I can train on trellises for my patio. There's lattice there, but not enough to block out neighboring home. This is a mobile home. Would love flow... See more
I am gluing some colored glass gems onto a glass window..
I am using E6000 to attach the glass gems to an old window. I want to make sure that everything will stay attached. I plan on spraying clear Krylon onto the whole gla... See more