How do I handle new hardwood floors that scratch really easily.
-
KMS Woodworks on Dec 21, 2011What type of finish was used?...oil based, water based. Catalyzed? How many coats?...how long has it been since the "finish" was applied...has it been allowed to cure properly? avoid the "wax" that will just contaminate any future "re-finish" or repair work that needs to be done. Check out this article I wrote on floor finishes...If you have more questions after that I will be glad to help you out. http://www.networx.com/article/exotic-wood-floor-finishes-you-havent-sHelpful Reply
-
-
Tamara S on Dec 21, 2011Thanks for the advise about the wax. I think they put polyurethane, maybe two coats and then they walked on it a couple days later. The builder was very, very behind on the schedule, blah, blah, blahHelpful Reply
-
-
Dan's of Central Florida, Inc. on Dec 21, 2011I try to put down at least 4 coats of poly to finish a floor, allowing a day dry time between coats if that is possible. Sometimes I have done 5 or 6 coats if the area gets really high traffic.Helpful Reply
-
-
Woodbridge Environmental Tiptophouse.com on Dec 22, 2011New finishes always seems to scratch easy. Add to that the contractor rushed the job and did not allow the new finish to properly harden adds to your frustration. Remember any new shiny surface will show even the slightest marks until it begins to wear and loose its shine. Add to that a perhaps darker finish and it even shows worse. You need to use the floor with care, any areas that are walked on, on a regular basis should have runners placed. Be careful however not to use runners with rubber backs as this will stick to the surface of the new wood. No shoes only socks, and forget about critters with sharp nails that will wear down the finish in short order. Do not wax the surface if it has been sealed with a poly finish. This type of finish takes a long time to completely dry, any wax surface will seal the coating thus preventing it from fully curing.Helpful Reply
-
-
Tamara S on Dec 22, 2011We are planning to be away from the Condo for a week in the Spring, should I have someone come in and add coats of Poly?Helpful Reply
-
-
KMS Woodworks on Dec 22, 2011I like to use a minimum of 3 coats...with a full day between. Many thin coats are better that a couple thick coats. The thinner the coat the faster it cures. Most floors should cure at least 72 hours ( three full days) before they see regular traffic...more time if the weather is humid. You mentioned poly as the finish used but not whether it was water based or oil based. You could have it "beefed" up in the spring. Have the floor lightly "screened" then have a few more thin coats applied with a solid three days to cure after the final...I like to use "satin" finish as the gloss finish only stays gloss for a short time once it starts to see wear.Helpful Reply
-
-
Tamara S on Dec 22, 2011Thanks, this was very helpful. Now to find the right contractor before Spring! THelpful Reply
-
-
Kathleen M on Dec 22, 2011I just wanted to add my two cents about wax. I had hardwood floors which I kept waxed in a home that I lived in for 20 years. It was a very high traffic home with dogs and kids, and the floors looked great when I moved out. (The floor waxer came every 3-4 months). I moved in to a second home, no kids, less traffic and the floors needed refinishing after 7 years. It is a giant pain to go through floor refinishing when you live in a house! I really wish I had kept them waxed. The finish couldn't be repaired because the floors had been stained.Helpful Reply
-
-
Woodbridge Environmental Tiptophouse.com on Dec 22, 2011Good points Kathleen, but one must remember when a new floor is just refinished waxing can really slow and even stop the drying process of the chemicals that are placed on the floor during the refinishing process. One should wait at least a year before putting any kind of polish on a newly finished floor.Helpful Reply
-
-
Tamara S on Dec 22, 2011Thanks Kathleen, THelpful Reply
-
-
Nichter's Home Services Corp on Dec 22, 2011Three coats is normal, and often best. I may have missed it, but I do not see whether the poly is a water or oil based. That info is important to my answerHelpful Reply
-
-
Tamara S on Dec 23, 2011I'll have to ask the builder, thanks THelpful Reply
-
-
KMS Woodworks on Dec 23, 2011As I mentioned in my article ( link posted in my first response) wax or a simple penetrating oil an be used as a stand alone finish. My master bedroom room is simply finished with some basic linseed oil. The wood is Jatoba (Brazilian Cherry) which is about three times harder than oak. With a finish like that touch ups can be done without any sanding at all. I recently touched up the area under Tori's studio bench where the chair feet had rolled about. Since there is no "layer" of finish on top the wood itself provides the "wear layer" this area was slightly lighter than the surrounding area. 10 minutes with a rag and a few drop of oil and it looks like the rest of the room. This floor is now 10 years old and still looks brand new. Keep in mind this is a bedroom and traffic is light...and dry. This type of finish would not holdup well in a Kitchen or heavy traffic area without more frequent care.Helpful Reply
-
-
Clay B on Dec 23, 2011Yes, more coats. One trick if you don't want glossy. Do 3-4 more coats of glossy, then top coat with semigloss or satin. Glossy is a harder finish.Helpful Reply
-
-
Nichter's Home Services Corp on Dec 25, 2011glossy CAN be harder if it is allowed to cure properly, because gloss has more solids.Helpful Reply
-
-
Tamara S on Dec 26, 2011Thanks, will keep that in mind when we have them add more coats in the Spring. THelpful Reply
-
-
Tamara S on Dec 31, 2011I'd like to thank everyone for the advice on my hardwood floors.Helpful Reply
-
-
Dan's of Central Florida, Inc. on Dec 31, 2011No problem Tamara, that's why we are here. Happy New Year!Helpful Reply
-
-
KMS Woodworks on Jan 01, 2012Tamara...I grew up in Michigan just north of Kalamazoo...and remember a Bellvue...between Battle Creek and Lansing...where is Belleville?Helpful Reply
-
-
Tamara S on Jan 02, 2012Off I94 between Ann Arbor and Romulus. It is a lake community, so I feel right at home. I grew up in Brighton and it is wonderful to be back in the country. But with the airport just one town over, for all the business travel we do!Helpful Reply
-
Related Discussions
How do I clean a really dirty really old hardwood floor?
The floor is original and was laid in the 1900's. It is toenailed. This apartment is that old. It is inexpensive and around the baseboards it looks like soot. It'... See more
Old desk with hard rubber top needs help
I have a very old desk that is in great condition except for the top. It is that old, hard rubber and it has a lot of dings and gashes (for lack of a better term). I ... See more
Do colors have to coordinate for bedroom and bathroom?
I recently got overzealous and bought a shower curtain, towels and rug for my bathroom in a totally different color than I planned on doing in the actual bedroom. Doe... See more
Should I remove plaster and lathe or can I just remove plaster?
I have an 1882 Balloon construction house that has some pretty extensive plaster falling off of the lath. I know that the lath actually adds to the wall stability, a... See more
How do I remove sand paint from the walls of a small bathroom?
Thought it was clever and a great look until I realized that if you fall against the wall it would scrape worse than a fall on cement. My husband is elderly and the l... See more
Has anyone had any luck removing artillery fungus?
Please provide personal success stories on how to get rid of fungus in mulch... not links because I have googled and watched others and tried. My daughter had a load ... See more
Which do you prefer: distressed wood or natural wood?
When it comes to choosing wood for your home decor, the finish can make all the difference in achieving the look and feel you want. Distressed wood, with its rugged c... See more