Crown Molding Questions.
-
The Money Pit on Jan 02, 2012Deborah, Crown Molding is hard for some contractors that just don't understand compound angles. Here is a DIY option that is simple and looks just as great: http://www.sosimplecrown.com/#. If is a foam product that is super easy to cut and install.Helpful Reply
-
-
Deborah C on Jan 02, 2012You would suggest this rather than the real thing The Money Pit? Have you seen this up? Does it look real?Helpful Reply
-
-
Wally Daly ,,Mastercarpenter,artist on Jan 02, 2012ask him how he cuts it,,,,if he says upside down and backwards ,,,,,you found your guy,,,,,,,on standard miter box,,,,on slide compound,,,it falls at 32.5 ,,,by i believe 27,,degree,,,but unless your a pro dont use slide compound ,,,,,,,,cut your hand off on kickback ,,good luckHelpful Reply
- See 1 previous
-
-
Woodbridge Environmental Tiptophouse.com on Jan 02, 2012The foam product that Money Pit suggested is fine if your painting it. Depending on the brand purchased it has corners already cut and all you do it butt the long lengths against it. If you have really long lengths in the room however I would suggest against it as it tends to swell in length and shrink as well. Causing in some cased it to open up at the seams. The art of doing good molding trim work is like many trades dieing with the invention of all these types of products. But depending upon the complexity of the crown your planning to install, will determine exactly who you need and or want to do the job for you. Perhaps contacting a good quality kitchen installer? These guys work with stain type trims all the time and with that kind of work they need to do the job right because they cannot simply fill in the spaces of a incorrect cut. So their work would need to be done better. Just an idea for you to ponder.Helpful Reply
-
-
The Money Pit on Jan 02, 2012Deborah, if you are painting it, then yes, this is definitely the way to go. Once installed, it is virtually indistinguishable from the real wood -- but is a lot less work to install.Helpful Reply
-
-
KMS Woodworks on Jan 02, 2012Crown can be a real bugger for some...Upside down and backwards is one way...but I have a nifty set of crown Molding "jigs" that come in the 3 basic "spring angles" that molding is made in. These jigs help a ton... http://www.cutncrown.com/ Paint grade molding is much easier as "mistakes" or minor variations in out of square walls can be easily covered with caulk...Stain grade work will need to be much more precise. And the skill of the carpenter will quickly become apparent Pricing will vary on many factors as I mentioned in this article I wrote on trim pricing. http://www.networx.com/article/how-much-does-it-cost-to-install-molding In the Photo below I installed over 2000 feet of trim in this home...some of it was crown...The rest was all custom milled window, door and base trim. In that Home I also refinished all of the interior doors and installed new stair railings.Helpful Reply
-
-
Glkirk Builders Inc. on Jan 02, 2012Deborah, May I suggest that you do your part in hiring any contractor. Have all the details fully documented so as to ask the carpenter to only have to install the material the way you have asked him to. What size and profile will this crown moulding be? Will it be one, two, three or more pieces? Are there specifications as to margins with numerous pieces? (I always made a Mock-up) What other details are pertainant? Will it be stain grade, paint grade, painted, stained? Thats your first hurdle. You are right and good in looking at prospective contractors work. A lot of general contractors don't know any where near how to install crown moulding. He will have a Trim Carpenter do the actual craft. Personally, I have only used the cope joints with oversized pieces. No scarf (Mid) joints if at all possible. Sorry to have to say it, but I have had to learn every single aspect and detail of every part of every project I have undertaken leaving nothing to chance or surprise. (good or bad) And I'm afraid you will have to also. Good luck.Helpful Reply
-
-
Posh Patios on Jan 03, 2012I always ask cope or miter? As soon as miter is mentioned it tells me speed not long term quality. Both joints look the same short term but not long term. There is a technical reason for the cope if they dont know the answer...they dont understand trim. Do they use glue? Is it finished grade of paint grade?Helpful Reply
-
-
Faidra at CA Global Inc on Jan 23, 2012Posh, what does "cope" mean versus miterHelpful Reply
-
-
Woodbridge Environmental Tiptophouse.com on Jan 24, 2012Miter is simply cutting angles into the lumber to create a corner or some sort of angle to fit around what ever it is your trimming out. A cope is part Miter but with the use of a coping saw. you back cut the miter so you end up with a sharp edge angle. This trim piece is then placed against the 2nd trim piece that was just cut off straight. The result is a more professional finish piece. This is done almost all the time when using woods that will only be stained as if done properly there is no gap left that is often the case with mitered joints. here is a U-Tube video on what I tried to say. http://www.youtube.com/watch?v=54bovMpEF0wHelpful Reply
-
-
Faidra at CA Global Inc on Jan 24, 2012Thanks WE as I am having the same issue in GA as the lady who started the thread. Moulding makes the difference in a home, but done incorrectly it can be a nightmare - one which I haven't woke from yet.Helpful Reply
-
-
Posh Patios on Jan 25, 2012The cope and the miter make look the same at the end of the day. However, over time the cope allows for proper wood movement. It takes longer to do and requires some extra skill so many people just miter the trim. A good trim guy can cope a piece of 5" crown in about 4 minutes.Helpful Reply
-
-
Dover Point Designs on Apr 26, 2015As a "Hands-on" Designer, Remodeler, I often do my own carpentry for my projects. However, I also have my "go to" subs which each have their specialties. You may want to contact a designer in your area, who can set up a simple consultation and also recommend their favorite millwork contractor. You would only need and hour or two with the designer to discuss crown ideas.Helpful Reply
-
Related Discussions
Vinyl plank flooring vs pergo (laminate)
I currently have stinky dirty carpeting in my living room and I want to replace it with a durable flooring that can stand up to dogs and kids.
How to remove popcorn ceiling that has been painted?
Does having a paint over a popcorn ceiling change how I'd remove the popcorn ceiling?
How to apply peel and stick wallpaper?
I want to spruce up my walls with peel-and-stick wallpaper. Has anyone used this before and can advise me as to how to apply it properly?
How to stain wood floor?
I've heard staining is a good technique for updating floors. So how do I stain my wood floor?
How much overage do you calculate in when measuring for crown molding?
Crown mouldings in kitchen I want replaced with a larger crown . This is my first time tackling this type project. What's a girl going to do😀. How hard is it to m... See more