how to break down a retaining wall??
-
KMS Woodworks on Jan 08, 2012Retaining walls are used in landscaping to keep hill sides from moving or collapsing. Inside a home, walls are either partition or load bearing. The design and layout of your home should provide clues as whether this wall is "load" bearing or not. Another consideration is what may be "in" the wall. Wiring, plumbing...a possible vent stack. If the wall is a simple partition wall this project would be rather straight forward...if it is load bearing ( ie : holding up the roof or second floor) then a supported header will need to be built into some type of arch or "opening". You may or may not need to bring in a structural engineer...it depends on you homes design etc. A number of years ago my brother opened up a wall in his 1920 bungalow. He had to put in a heavy duty beam as there was second floor ( brick ) wall that needed to be supported. Needless to say is was a big beam.Helpful Reply
-
-
Linda M on Jan 08, 2012ok thanks its a partion wall looking to make two small rooms into one big room any feed back would be appreciated Thank You so much :-)Helpful Reply
-
-
KMS Woodworks on Jan 08, 2012Your first step is to have a Builder or engineer take a peek to see what type it is. In the case of a load bearing wall the header will need to be supported by columns...this load will need to be transferred Down through the basement or crawl space to a "foundation". In many of these cases a temporary 'support" wall is constructed until the new structural elements are in place. Once the loads are taken care of its pretty simple from there. If the floors are hardwood it may require some fancy "lace in" work to make the place look more like "one" room.Helpful Reply
-
-
Linda M on Jan 08, 2012one room is hard wood floor and the other is carpetedHelpful Reply
-
-
HandyANDY - Handyman & All Repairs, LLC on Jan 08, 2012As KMS is mentioning, you probably do want to have an engineer take a look at it or at least a licensed GC in your area. The journal of light construction will have some online articles you can read for info on how to build a new built-up header to take the load properly. We've done 100s of these over the years.Helpful Reply
-
-
Nichter's Home Services Corp on Jan 08, 2012Lnda, it would be irresponsible for anyone online to tell you how to take this wall out without strong evidence that it is indeed only a partition wall and not a load bearing wall. You DO need a professional to assess that.Helpful Reply
-
-
Linda M on Jan 12, 2012not doing it till March THANK YOUHelpful Reply
-
-
Nichter's Home Services Corp on Jan 13, 2012That is good, because it can take 2-3 months to get engineering and permits done so you are ready to startHelpful Reply
-
Related Discussions
Retaining wall fell down... need some advice please!
Hi everyone! The old, stacked stone & mortar retaining wall we had in front of our house fell down after all of the rain we had in the Midwest last week. As you can s... See more
How do I paint amber colored window glass?
The entry door on our house (on the home when we bought it) is a very sturdy door, well made door, but very ugly. The top half has a diamond grid with amber glass. I ... See more
Painting glass candle holders
What kind of paint should I use to make cake stand.
How to make a balloon garland?
Does anyone know how to make a balloon garland or a balloon arch?
Blackout curtains behind vertical blinds
I have two 6' patio doors, and I want to add blackout curtains to keep the sun/cold out. What is the best way to hang them, and what can I use to push the curtains ba... See more
Cleaning stained china tea cups
I have a set of china that belonged to my grandmother back in the '40's. Most of the pieces are still beautiful except one cup that bears cracks inside with perhaps c... See more
How to clean my kitchen cabinets from grease?
My kitchen cabinets are embarrassingly greasy. Please share your degreasing tips with me so I don't have to cringe every time I glance at my cabinets.