how to break down a retaining wall??
-
KMS Woodworks on Jan 08, 2012Retaining walls are used in landscaping to keep hill sides from moving or collapsing. Inside a home, walls are either partition or load bearing. The design and layout of your home should provide clues as whether this wall is "load" bearing or not. Another consideration is what may be "in" the wall. Wiring, plumbing...a possible vent stack. If the wall is a simple partition wall this project would be rather straight forward...if it is load bearing ( ie : holding up the roof or second floor) then a supported header will need to be built into some type of arch or "opening". You may or may not need to bring in a structural engineer...it depends on you homes design etc. A number of years ago my brother opened up a wall in his 1920 bungalow. He had to put in a heavy duty beam as there was second floor ( brick ) wall that needed to be supported. Needless to say is was a big beam.Helpful Reply
-
-
Linda M on Jan 08, 2012ok thanks its a partion wall looking to make two small rooms into one big room any feed back would be appreciated Thank You so much :-)Helpful Reply
-
-
KMS Woodworks on Jan 08, 2012Your first step is to have a Builder or engineer take a peek to see what type it is. In the case of a load bearing wall the header will need to be supported by columns...this load will need to be transferred Down through the basement or crawl space to a "foundation". In many of these cases a temporary 'support" wall is constructed until the new structural elements are in place. Once the loads are taken care of its pretty simple from there. If the floors are hardwood it may require some fancy "lace in" work to make the place look more like "one" room.Helpful Reply
-
-
Linda M on Jan 08, 2012one room is hard wood floor and the other is carpetedHelpful Reply
-
-
HandyANDY - Handyman & All Repairs, LLC on Jan 08, 2012As KMS is mentioning, you probably do want to have an engineer take a look at it or at least a licensed GC in your area. The journal of light construction will have some online articles you can read for info on how to build a new built-up header to take the load properly. We've done 100s of these over the years.Helpful Reply
-
-
Nichter's Home Services Corp on Jan 08, 2012Lnda, it would be irresponsible for anyone online to tell you how to take this wall out without strong evidence that it is indeed only a partition wall and not a load bearing wall. You DO need a professional to assess that.Helpful Reply
-
-
Linda M on Jan 12, 2012not doing it till March THANK YOUHelpful Reply
-
-
Nichter's Home Services Corp on Jan 13, 2012That is good, because it can take 2-3 months to get engineering and permits done so you are ready to startHelpful Reply
-
Related Discussions
Retaining wall fell down... need some advice please!
Hi everyone! The old, stacked stone & mortar retaining wall we had in front of our house fell down after all of the rain we had in the Midwest last week. As you can s... See more
Where is your favorite place to shop: Dollar Tree, Walmart, or Target?
Let's chat about our go-to shopping destinations! Whether you're on the hunt for budget-friendly bargains, everyday essentials, or trendy finds, we all have our favor... See more
How to replace a toilet seat?
I need advice on how to replace a toilet seat, please. What do I need to know when looking for a new one?
How to stop raccoons from climbing onto my deck
They are also washing their food in my pool. Help?
Indoor furniture turned outdoor furniture
What kind of paint could I use to turn this indoor dining set into outdoor set? It would be exposed to the sun and rain and our dogs here in North Texas. The set belo... See more
How to remove burnt pasta stuck at the bottom of a pot?
Burnt pasta stuck at bottom of pot - how to clean a burnt pot to remove the food?
My toilet handle stays down when you flush and the water keeps running
how do I fix my running toilet?