Replacing a lock
-
Debbie Harris on Nov 12, 2013Longer screws with some glue under the plateHelpful Reply
-
-
Lauren of Mom Home Guide on Nov 12, 2013Great idea, Debbie! I was thinking of using longer screws, but wasn't sure if that would work. Maybe I can also use some Gorilla Glue. I used that to better adhere a towel bar that wasn't tightly enough attached to the wall (because of the screws in drywall), and it's been adhering nicely for a few months now!Helpful Reply
-
-
Vicky Johnson on Nov 12, 2013poke toothpicks in the holes and break off.....put enough of them to make them tight and then use your screws and they will screw tight again.Helpful Reply
-
-
Lauren of Mom Home Guide on Nov 12, 2013Another great idea! Thanks, Vicky!Helpful Reply
-
-
Joy Derouen on Nov 13, 2013Lauren you can use golf tees in the holes and break them off even with the door. That way you have a little more wood for the screws to bite into.Helpful Reply
-
-
Lauren of Mom Home Guide on Nov 13, 2013Thanks for the tip, Joy!Helpful Reply
-
-
Sandra Cook on Nov 13, 2013You might try bigger, not necessarily longer, screws. And you can fill in the existing holes with putty just for repairing wood. Can even use autobody putty. Let it harden and and re drill your screws. Toothpicks etc can shift over time and rot. And I personally would avoid glue under the plate as at some point you may have to replace it again and it will damage your door if you remove it. Good luck.Helpful Reply
-
-
Lauren of Mom Home Guide on Nov 13, 2013Thanks, Sandra -- I was thinking of trying wood putty! Maybe I will try thicker and longer screws!Helpful Reply
-
-
Jeanne888 on Nov 13, 2013Lauren, BEFORE YOU DO ANYTHING ELSE, try this. Get a tube of graphite (from the key-making station at Lowe's, Home Depot, or hardware store) and squirt the heck out of the tube into the door lock. Squirt onto the key as well. Then try inserting the key into the lock and turn back and forth. If it doesn't work, squirt some more. If that still doesn't work, then replace the lock. From my experience, graphite will solve many of the problems with reluctant or sticking locks. Graphite is a dry lubricant that every homeowner needs. And it's cheaper than replacing a lock.Helpful Reply
-
-
Jeanne888 on Nov 13, 2013Sorry, I should have explained: I meant, before you replace the lock. Certainly, try the solutions above to fill the holes for the screws. I like the golf tee idea. I often use wooden toothpicks with white glue for smaller screw holes.Helpful Reply
-
-
Liliana Wells on Nov 13, 2013I like Vicky's, Joy, and Jeanne888 ideas. My husband also swears by WD40 as a lubricant when metal to metal moving parts are involved. Good luck.Helpful Reply
-
-
Lauren of Mom Home Guide on Nov 13, 2013Thanks so much! I will give that a try, Jeanne.Helpful Reply
-
-
Jeanne888 on Nov 13, 2013I also use WD40, mostly to prevent rust from forming after I've removed it from a tool or metal part. But not in locks. Before it dries, WD40 is wet and attracts dust, so it is not good for locks. Graphite is dry and so does not attract dust.Helpful Reply
-
-
Vicky Johnson on Nov 13, 2013I usually squeezed glue in after I poked them in there....I never thought about a golf tee for bigger holes!Helpful Reply
-
-
Jill on Nov 13, 2013If you end up replacing the entire locks on the door, it's easy to replace. If you wish to use the same key as you have now, simply replace the cylinder pins that you can purchase as a kit with the locks at any hardware store where you get the locks. It's easy enough and sometimes you will find they will even change out the pins for you for a small fee. Simply fill the screw holes just as you have been told above with either toothpicks, or a golf tee.Helpful Reply
- See 1 previous
-
-
Jeanne888 on Nov 14, 2013I just had to replace my back door lock, and whaddya know? If you have a Kwikset lock, there is now a one that you can use your original key on! You can do it yourself. No pins or even opening up the lock. Easy peasy. And you can do it again and again, whenever you want to change the key.Helpful Reply
-
-
Lauren of Mom Home Guide on Nov 14, 2013I saw that lock but was afraid to try it. I am glad to hear that it's easy to use -- we have Kwikset locks on our doors. Thanks!Helpful Reply
-
-
Lauren of Mom Home Guide on Nov 14, 2013Cool -- I am going to have to do some thinking! I like the idea of a keyless lock, but my spouse is very old school, so he probably wants a regular lock. Thanks, Jill!Helpful Reply
-
-
Lauren of Mom Home Guide on Oct 21, 2014Wow. Sorry to hear that, Tara!Helpful Reply
-
Related Discussions
How to get rid of mice?
We seem to have some unwelcome Mickeys and Minnies in our house. What is the best way to get rid of them?
How to remove popcorn ceiling with asbestos?
I want to remove my popcorn ceiling, but it has asbestos in it. How do I go about this safely?
How to caulk baseboard gaps?
How do I fill gaps at baseboard, should I caulk? If so, does anyone know how to caulk baseboards?
How to fix squeaky hardwood floors?
How do I fix squeaky hardwood floors?
1975 balcony railing too low, not to code
our new home has balcony that was to code in 1975 for hight but way too low for us, below our waist, easy to go flying over. Can not afford a new one, still have home... See more
Open shelves and a 1 year old. Suggestions?
The 1973 double oven in my rental broke, a new range was put in and the old oven space was filled with open shelves. I have a 1 year old who likes to climb!! Please ... See more