DIY Concrete Lamp - Led String Light

Glen
by Glen
11 Materials
$35
2 Days
Medium

I used these lights for an end table. What's nice about these lights is that all the electronics are hidden. It's a simple project that requires very little tools and can enhance any space. For more awesome DIY be sure to check out my youtube channel www.youtube.com/c/DIYCreators

Here is a step by step video to make this lamp.

It's a simple project that requires very little tools and can enhance any space.

I cut the PVC first to create a straight edge. Then I set my stop block to make a 5 inch cut on the miter saw. You can make as many as you'd like, but I made two. Since the piece of pvc was outside collecting dirt, I gave them a quick wash down so no dirt transfer to the form. Since the piece of pvc was outside collecting dirt, I gave them a quick wash down so no dirt transfer to the form.

The form needs to be hollow on the inside to hold the LED controller. You can use what ever you come up with. I used two water bottles as a place holder.

Keep in mind the water needs to me centered in the form. I made the water bottles 1.5 in below the rim of the PVC.

The top of the form need to be small enough at the top for the vase to cover. I used a (1 inch) foam weather strip to prevent the cement from filling this area.

To cover the bottom of the PVC I used plastic wrap . Then used masking tape to hold it in place.

Then I took a bucket, added concrete then water. I mixed the concrete with a small shovel.

I placed the bottle in the center then poured the cement mix. I added a small amount then used a mallet or a hammer to tap the outside of the PVC.

This helped the cement fall to the bottom. When I was tapping the PVC I noticed the bottle was attempting to rise to the top, so I kept an eye on the bottle.

Then I used the sander. During the vibrating process I used a nail to hold the bottle down.

I let the form sit for a few days to cure. The bottom was completely covered with concrete. Not a big deal I took a hammer and broke the thin layer. Now I normally use some kind of oil to help with the release process. However I forgot to add oil. To remove the PVC I made two cuts 2 to 3 inch apart. I made sure to not go all the way through the PVC while using a hack saw. Try not damage the form. Then I pulled and cut the section out. The PVC released easily.

I didn't sand the body of the form. It was very smooth. The top however required some work because the vase didn't fit. This was something I knew I would have to address before I started. To sand the I used a 60 grit sand paper. Then I drilled out the top with a masonry bit . The bit pressed down on the plastic bottles so I was forced to remove it. My intention was to keep it in the form. Not a big deal though. Next I notched out a channel for the power wire to pass through.

Then I passed the string lights through the hole. I connected the light to the controller and then the transformer to the control. Then I placed it inside the concrete. I applied hot glue to the channel then placed the wire in the channel. Add a little more glue on top. I didn't show it, but I also added hot glue to hold the IR in place.

I installed the wire in the vase and placed the vase on the concrete base. Plugged it in and was ready to go!


For more cool projects visit my website www.diycreators.com


Follow me here:

Subscribe to my YouTube channel for weekly videos:   https://goo.gl/aWzL1T

Follow me on Instagram for daily post: instagram.com/morediycreators


DIY home decor using recycled plastic bottles

For more creative DIY home decor ideas, discover the top things you can make with repurposed plastic bottles here.

Resources for this project:
See all materials
Any price and availability information displayed on [relevant Amazon Site(s), as applicable] at the time of purchase will apply to the purchase of this product.
Hometalk may collect a small share of sales from the links on this page.More info
Frequently asked questions
Have a question about this project?
3 of 18 questions
  • Tim Walters Tim Walters on Mar 02, 2021

    I was not able to open the website... I am very curious about other creative ideas!

  • Vineethayvs Vineethayvs on May 30, 2021

    icon can you wear hand glouses ?

  • Silviastar Silviastar on Jul 18, 2022

    What a beauty! I want such a lamp in my country house. It would go very well with my interior. I decided to install LED lighting in the bathroom respectively. The power supply is suitable for me only sealed. It is protected from moisture. Honestly, I wanted to buy a regular one without thinking about such an important point.

    Please tell me how easy it is to change the bulbs in a lamp? I always think ahead. Will I be able to change it without outside help?

    I need to buy several packs of these bulbs at once. It would also be interesting to hear feedback from those who have already used such bulbs. What do you think? Is it worth buying a lot of them for lighting? Or is it more about the decor? To install and admire this beauty.

Comments
Join the conversation
2 of 333 comments
Next