My house is about 10 years old and there are a fair number of areas where the seams between the drywall sections are
I'm assuming that I'd have to remove all of the sealing tape along these areas, retape and then apply the mud again and sand, which will be very dusty, so I want to fix it so that it won't need to be done again in the near future. What's the best way to do that?
-
Nichter's Home Services Corp on Dec 10, 2011It might very well have been a decent job to start, but if the house has large temperature fluctuations, the thermal movement of the materials would cause cracks like that, esp in the garage and areas with large surfaces like a ceiling. I also see far more of these small cracks in SR that was taped with the FG mesh tape rather than paper tape. Yes, the fix is to re-do itHelpful Reply
-
-
Peace Painting Co., Inc. on Dec 10, 2011Rich, one prevalent problem in garage drywall is the use of interior drywall and interior paint in an exterior application, which can lead to seam cracking and tape coming loose. Or as you stated, the compound or mud could have frozen before it dried, leading to failure. Either way, if the tape is not loose or bubbling off, you do not have to remove anything. I do like the idea of going back over it with fiberglass tape because it is made to flex more than the paper tape. However, the drywall must be stable or no tape will hold. This means that there should be no movement at the joints when you push on it. I wish you luck in floating out these seams. It takes someone with experience to make it look decent. After it is re-taped and re-skimmed, you have the option of using a texture or sand finish paint to cover the imperfections, and it looks quite nice. Be sure to use exterior rated primer and paint this time! Best, CharlesHelpful Reply
-
-
Peace Painting Co., Inc. on Dec 10, 2011Cute puppy dog to keep you warm on those three dog nights in WV.Helpful Reply
-
-
Woodbridge Environmental Tiptophouse.com on Dec 10, 2011Builders are only responsible for taping one coat on the garage wall to create a fire resistant barrier. They do not tape this nearly as well as they do inside of the home. Most likely the taping job utilized the least amount of taping compound that would hold the tape into place. Pull off any loose tape, and re-tape it using spackle mix out of the bag and fiberglass tape. It will harden faster so mix a little at a time and work fast. This being done properly should prevent future failures of the wall.Helpful Reply
-
-
Dan's of Central Florida, Inc. on Dec 10, 2011If dust is a concern while sanding drywall mud, then a "wet-sand" can clear this up. First, use a drywall knife or a putty knife to scrape/slice down and high ridges. Then use a damp (not wet) sponge to do the sanding. It will wet the drywall compound just a bit and allow you to smooth it out. The damp sponge itself will catch/clean up any dust that is created. Those thick, yellowish colored sponges work well for this.Helpful Reply
-
Related Discussions
Blackout curtains behind vertical blinds
I have two 6' patio doors, and I want to add blackout curtains to keep the sun/cold out. What is the best way to hang them, and what can I use to push the curtains ba... See more
How do I stop the pitting on my stainless steel refrigerator?
I have a 7 month old Frigidaire brand stainless steel refrigerator and I noticed pitting and rust spots numbering somewhere around 30 or 40. Is there something I can... See more
How many solar panels do I need for 1600sq. ft home?
How do I make fall leaf luminaries?
I saw someone making gorgeous luminaries with fall leaves, and I want to give it a try. Do you have any ideas on how to make them?
Where can I find a plastic version of cinder blocks?
I want to decorate my roof garden with benches and shelves, but don't want to invest in the weight.