Any suggestions for installing laminate counter tops?
Any suggestions are welcome.
Thank you
-
Straight Nails Construction on Apr 28, 2012First, measure your actual corner. Do not assume that it is a 90 degree angle. Any variance will allow for your cut to be wrong. Once you measure your corner, divide it in half and that would be your actual angle. (in other words, if your corner is actually 90 degrees, your cut would be 45 degrees. If it is 92 degrees, your cut would be 46 degrees). You can buy a kit that will allow you to "clamp" your corners together. Assuming you are cutting with a circular saw, buy a blade that has the most teeth that your saw can accomidate. Usually a 60 tooth blade would work. Clamp something sturdy like a 4 foot level against the countertop with clamps, so that the circular saw fence will ride along that straight edge, which usually makes a much straighter cut. Place duct tape along the cut line that you are going to make. This will help to prevent any "chipping" that may occur. Use the longest level you have to measure/level your cabinets without countertops. If your cabinet doesn't have a very slight pitch towards the external side of kitchen, shim the countertop so that they do so. The reason for this is as water sits on the countertop, this (again I say VERY slight) pitch will allow water to run towards the floor, and not back against the wall/backsplash. Use a standard adhesive that can be placed on top of the bottom cabinet walls, and the countertop can sit on. Then, find some strategic places to place some wood screws through the bottom of the cabinets into the countertop. It is VERY important to not place a screw that is longer than the thickness of what you are screwing through and the depth of the countertop. The screws are nothing more than to put some resistance to the countertop to secure to the cabinets. The glue you use will do most of the work. If you place them at an angle, this will take more distance when you place them. Use a silicone based caulk when you caulk against the wall to deter breakdown from the water that will splash upon it.Helpful Reply
-
-
Designs by BSB on Apr 28, 2012Great guideance from Straight Nails. I am not surprised at the locals avoiding the job. Ive never known an installer or custom shop to take on "post form" counter tops and do the miter joint themselves. Risk is high for a miter cut.. and the whether they can get a smooth joint w/o a bolting system. Ive never seen/heard of anyone but the counter top vendor make this cut. The miter cut is not only about the cut, but they bore holes in the bottom side for the use of clamps to pull the counter top together to hold the glue.. as it dries. You may want to ask your home center if you could bring the tops to the vendor to have them make the cuts for you. Installing would be much a bit easier thereafter.. or at the least, it would be easy to find an installer.Helpful Reply
-
-
3po3 on Apr 28, 2012Again, great tips from Straight Nails. The only slight change I would make is to suggest putting down masking tape along the edge. It will still prevent chipping but is easier to pull up without leaving any residue.Helpful Reply
-
-
Debi M on Apr 28, 2012My hubby installed ours and he is not a carpenter, just a Mr. Fix It. Great advice on the tape to get a smooth cut. Hubby's rule is measure twice and cut once.Helpful Reply
-
-
Woodbridge Environmental Tiptophouse.com on Apr 29, 2012you must cut from the back side of the top when cutting. Also use a new highest tooth count carbide trim blade that will fit your saw. install a guide board with tiny screws fastened to the top to keep your saw exactly where you want it to be. You cannot follow a pencil line close enough to not have a gap when both sides come together. I have done several of these cuts before and they all turn out fine. The biggest trick is to be sure you are cutting the angle correctly . I would suggest that you take a 2 foot wide by half inch thick plywood section to mimic the top and place the plywood into the corner with one section overlapping the other. Then screw them to make your corner angle. Then from where the inside and outside corner meets draw a line from each and cut exactly from corner to corner. then take out the screws and place each panel onto the laminate slab and you now have your exact cut to transcribe onto the new slab. Move each template back the distance that your saw base requires, (typical saw bases are 2.5 inches away from side of blade) fasten each template and use its angle as the guide for the saw. You will get an exact angle cut that will perfectly match. Another method of making sure you get a tight match is to after cutting take a straight router blade set the counter at the proper angle with just enough space between each edge so only a 1/16th is removed from both sides at the same time. This will make the joint very tight. But if you follow the template method, use a new multi tooth blade for trim your cut will be very sharp and the joint will be as small as it can possibly become.Helpful Reply
-
-
Linda on Apr 29, 2012Thanks so much for all the suggestions. It sounds like precision measuring and cutting is the key to the best miter cutHelpful Reply
-
-
Linda on Apr 29, 2012@Straight Nails - excuse me for my ignorance, but what measurements would I use to determine the miter angle? What tool would I use to make this measurement? Thanks.Helpful Reply
-
-
KMS Woodworks on Apr 29, 2012This is one reason why I prefer to work in tile....large miters are avoided. and complex angles can still be usedHelpful Reply
-
-
Linda on May 03, 2012Thanks for all the suggestions. I like the template idea and will try that out this weekend.Helpful Reply
-
-
Straight Nails Construction on May 03, 2012Linda, I have a device called The original miter angle that is a great tool to measure corners. I have different sizes to use depending on the size of the project. There is also a way to measure a distance down each wall, then measure between the two points to calculate the angle degree, but I cannot remember how to do that. Once I remember, I will send another note.Helpful Reply
-
-
Linda on May 04, 2012Thanks Straight Nails. I need all the help I can get :-)Helpful Reply
-
-
Linda on Dec 27, 2012A Christmas miracle happened. I was finally able to find a handyman and his apprentice to install my laminate counter tops. I am very happy with the results. I am now priming and painting the cabinet bodies and new doors/drawer fronts as the weather allows.Helpful Reply
-
-
Linda on Dec 27, 2012I tried to post photos of the finished counter top/sink and stove but I am unable to :-(Helpful Reply
-
-
Straight Nails Construction on Dec 30, 2012Too bad, we would love to see the finished product. Glad you found someone to assist you with this....Helpful Reply
-
-
Linda on Dec 30, 2012I emailed the tech help dept at Hometalk - maybe they can help me post the photos. Otherwise, I might start a new post with the results.Helpful Reply
-
-
Linda on Dec 31, 2012Lulu (help desk) was able to upload the photos for me. Check them out and let me know what you think about the installation.Helpful Reply
-
-
Straight Nails Construction on Jan 03, 2013Looks good... nice choice of faucet hardware...Helpful Reply
-
-
Linda on Jan 03, 2013Thanks. I am going with Satin Nickle on all the hardware. I am hoping to get the first coat of final paint on the cabinet doors this weekend.Helpful Reply
-
-
Lola on Mar 20, 2015Fantastic job!Helpful Reply
-
Related Discussions
Vinyl plank flooring vs pergo (laminate)
I currently have stinky dirty carpeting in my living room and I want to replace it with a durable flooring that can stand up to dogs and kids.
How to remove popcorn ceiling that has been painted?
Does having a paint over a popcorn ceiling change how I'd remove the popcorn ceiling?
How to apply peel and stick wallpaper?
I want to spruce up my walls with peel-and-stick wallpaper. Has anyone used this before and can advise me as to how to apply it properly?
How to stain wood floor?
I've heard staining is a good technique for updating floors. So how do I stain my wood floor?
Should I re-stain or paint my cabinets?
Edit:””” 3 years later😂 I decided to paint them white and I am so very pleased with the results!We bought a new house with these ugly cabinets. I really cann... See more
Help me with my kitchen - strange layout with 3 doors in it!
I am looking for BUDGET options for my kitchen. It is very strangely laid out. I have 3 doors (laundry, bedroom and outside) that do not help the layout. I am planing... See more