Dust collection on Compound miter saw
-
3po3 on May 01, 2012I think ShopVac makes dust bags for these situations. I know people use them for drywall dust but it could work for your situation.Helpful Reply
-
-
KMS Woodworks on May 02, 2012I second Steve comment...I have 8 and 5 gal "shop vac" brand shop vac and use the disposable "bags" the foam and or pleated filters do not collect as much fine material. prior to using it is important to clean the motor assembly I use my air compressor and nozzle to remove any "dust" from the inside and out of base as well as the motor assembly. My miter saw in my shop in not hooked up to my dust collection systems. It just hits the wall behind it. now and then I just suck up the sawdust. I really only use my collectors for my planer, jointer and table saw.Helpful Reply
-
-
Woodbridge Environmental Tiptophouse.com on May 02, 2012You must be carefull when using a vacuum to catch this fine dust. This can cause an exposion if not properly handled. Dust bags designed to be used with shop vaccums are the best way to keep this stuff under control. Combined with a high end pleated filter you should be fine. Another way to keep this under control is to install a small dryer vent hood on an outside wall and pipe the discharge end of the shop vac out that opening when its in use. The fine dust will be expelled to the outside of the room. But remember as KMS said, you need to clean the vacuum as dust will collect on the fins of the blower and on the motor as well. The last method costs a bit more, but its well worth it if you do a lot of wood working. A cyclonic vacuum designed to collect dust is exactly what you want. They do not cost as much as you would think, and can be installed outside with just a hose system running in the shop so you do not have to hear them run while you cut wood. Here is a link for one that is not that expensive and works pretty well. http://www.harborfreight.com/2-hp-industrial-5-micron-dust-collector-97869.htmlHelpful Reply
-
-
Douglas C on May 14, 2012You must watch out for static electricity.....when you vacuum dust it creates static and that is what will get you in trouble. Google for ways to stop this.Helpful Reply
-
-
KMS Woodworks on May 15, 2012I have my main 2500 cfm dust collector plumbed directly outside. I will sometimes move the hose about when it is running. The static is REAL as I have been shocked a few times...a bit like running wooly socks over the carpet and touching a metal door knob.Helpful Reply
-
Related Discussions
How do I get grass out of a phlox bed?
This flower bed is extremely dense with phlox. Last year, I pulled much of the grass out by the roots, but it came back with a vengence this year. We've had a ton of ... See more
How can I remove a magnetic door knocker from a metal door?
The magnet in the knocker has "welded" to the door and seems impossible to remove. I have to paint the door so if the paint is damaged its not a problem.
How to remove rust from exterior door hinges without removing them?
GNATS - How to get rid of them?
Somehow my house and garden got tiny gnats that killed my fuchsia plant and fly everywhere. I have tried ALL the Web recommendations - soap and oil dishes, sand in th... See more
How do I remove hard water deposits from stainless washing machine tub
My new home's washing machine appears to have a rough buildup near the top of the stainless tub. I have run Affresh through the unit but this remains. I don't want to... See more
How do we remove calcium deposits on our patio water fountain
How do we remove calcium deposits from our patio fountain and brick walkway?
Hardwood Floors or Carpet in Bedroom: What's Your Preference?
Hey Hometalkers! We've got a cozy debate going on here: when it comes to bedroom flooring, do you lean towards the warmth of carpet or the timeless elegance of hardwo... See more