Severe storm leak
-
Home Repair Tutor on May 23, 2012Jane, Would you be able to take a few photos and add captions. Sorry to hear about your water leak, it's always frustrating to find these problems.Helpful Reply
-
-
Woodbridge Environmental Tiptophouse.com on May 23, 2012If the addition attaches to the side of the original roof, the flashing perhaps where the new roof meets the wall area may have not been high enough. Blowing rain can go uphill really easy and over the top of the flashing causing the leak that you have. The only thing I can advise you without looking at it, is not to have a reaction to taring up every space between the siding and roof. Sealing the space between the roof and bottom of the siding is one of the biggest mistakes I have seen when it comes to trying to stop leaks. Even sealing valleys in an attempt to stop a leak only causes more issues then it solves. Water must always drain out. And putting any kind of tar or caulk on the roof shingle joints, or between roof and wall areas where you would think the leak is occurring will only cause water to build up and not drain out. Resulting in more hidden damage and costs in the long run. The only tried and true method other then opening the wall or ceilings is to take a hose when its dry out and spray one area at a time mimicking the rain storm in direction until you begin to see the leak. This will narrow your issue down and result in the proper identification of where its happening and help you make the right repair the first time. You must also remember. Water can leak on one side of the house and show up on the other. If the door was an old window. your leak may be way up top, far beyond where you think the leak is now coming from. In any case do not simply tar or caulk every opening you see until your sure that is where the leak has come from, and then take that area apart and fix it correctly, not with just a tar or caulk patch.Helpful Reply
-
-
KMS Woodworks on May 23, 2012This is more common that some folks think. When windows are replaced (or doors) and the siding is now completely removed "proper" flashing methods are often skipped because it is a lot of work to remove all of the siding for that area and layer up normal levels of flashing / water proofing etc. Most of these installs are just band aid jobs with caulk trying to fill to roll of proper flashing etc. It would be my guess that this caulk has failed and would need to to upgraded.Helpful Reply
-
-
Melodie M on May 23, 2012You are going to want to dry out what got wet..especially if it went into the wall or you could get mold growth. you might be able to seal it with "Flex seal" and then paint over it...but a proper install should take care of it as well.Helpful Reply
-
-
Jane B on May 23, 2012HRT, there's really nothing to take pictures of. My neighbor, a former roofer and now an inspector for an insurance company, came over this morning because he saw me outside last night eyeing the addition between downpours (it went on for hours). He went up on the roof and reported that the high wind had lifted the shingles around the house/addition joint slightly and allowed a little water to get in. He checked inside and didn't see a problem because there was no sign of water damage. I have an attic entrance in my bathroom for the HVAC venting, and he looked up in there to make sure everything was all right -- again, no sign of water damage, not even any signs of dampness from last night. He felt around and said he only felt a tiny bit of dampness that should resolve today or tomorrow. He also said the shingles will flatten back down with a day of sunshine. So it seems everything is all right. I appreciate all the answers and concern!Helpful Reply
-
-
Home Repair Tutor on May 23, 2012Sounds like you're in good shape Jane. Have a great holiday weekend.Helpful Reply
-
-
Bernice H on May 24, 2012I bet you gave a big sigh of relief! Nice neighbor ...with pretty good news! And thanks for the post , I learned a lot here, and will share with my non handy hubs!Helpful Reply
-
-
KMS Woodworks on May 24, 2012I would still keep an eye on it....If you neighbor just looked and did not "do" anything...what is to prevent this from happening again when the next storm comes in? Check out this article I wrote on storm proofing your roof. http://www.networx.com/article/storm-proof-your-roofHelpful Reply
-
-
HandyANDY - Handyman & All Repairs, LLC on May 24, 2012I agree with KMS, keep an eye on it...wind damaged shingles are just that...wind damaged shingles that need to be sealed with something like Thru the Roof elastromeric roof sealant....or replaced. They will not just "warm" up an lay back down....once damaged....the wind will hit them again & again until they tear off.Helpful Reply
-
-
KMS Woodworks on May 25, 2012To add to Handy's comments....Shingles only comprise a "part" of the entire roof "system". The individual component parts each play their own role in keeping the rain out. Underlayment, flashing, shingles, drip edge...etc....as a stand alone item none will do the job....it is the combined effects of the entire roof system that works... when one component of the system fails the entire system is compromised until that failed component is fixed.Helpful Reply
-
-
Woodbridge Environmental Tiptophouse.com on May 25, 2012There is still another issue here. Even if the shingles blew up and allowed rain to get under, this can happen even if they do not lift. The seal tab does not prevent water from blowing up under the shingle. The concern here is that the roof pitch is not enough or the exposure is not proper to compensate for the flatter pitch. Still another concern is the flashing methods used and if who ever did the roof used ice and water shield assuming this was done in the past 15 years or so. But KMS your correct there are many parts of the roof system and although only one part seems to be at fault, I have a feeling its something else that should have worked and did not which is really the bigger issue here. If things were correct you should be able to blow the entire tab off and still not have any leak. personally I think there is a incorrectly installed or faulty flashing issue here. And the shingle has only brought it to light.Helpful Reply
-
-
KMS Woodworks on May 26, 2012I have seen many ( and repaired) many roofs where courses of shingles were completely missing...yet there were no leaks...at least at the time of my repair......this is due to underlayment and flashing doing their part. With those parts exposed they will eventually fail as the shingles provide the primary level of protection ( UV, hail, snow rain wind...) Poor Roof pitch and flashing mistakes are leading issues for leaks.Helpful Reply
-
-
HandyANDY - Handyman & All Repairs, LLC on May 28, 2012That's a good point...what kind of pitch is on this roof? Post us a pic!Helpful Reply
-
Related Discussions
How do I take off hard water from my tub?
Here’s my issue I have been living in the same apartment building for 18 years and I have a tub that deals with hard water on a daily basis. What is the best way fo... See more
How do I remove paint from painted tile and tub?
How should I remove paint from a tile floor and a bathtub?
What can I use to stop flies from collecting on my new deck?
My deck is new , I was told flies are attracted to the sap of the wood,.
What could be causing a wet floor, if a plumber finds no leaks?
wet floor under sink dry iu and run water no leak? no smell all is clean. run water both tubs, garbage disposal, use sprayer everything underneath stays dry. Go away ... See more
How to hide a pool filter?
Looking to hide this very hideous area. Thinking of a portable coat rack that you use when you have company. Bc it has wheels and can be moved easily.We still have to... See more
How to install a smart thermostat on my furnace?
Furnace is a Slant/Fin VSPH-90 boiler. There are three thermostat terminals at the boiler end, but only two have wires connected to them (see photo). The two wires co... See more