We have a covered entry way where the previously installed tiles have failed/broken up.
As I cleaned/took the tiles off, the sharp edges of the surrounding concrete broke off leaving ragged edges that need to be trimmed off in order to re do the tile or even just to fill the area with concrete. Want to know:
1. Is it possible to clean-cut the existing concrete?
2. Is it possbile to patch(repair) the existing ragged concrete edges?
Would greatly appliciate any comments and/or suggestion.
Yung
Attachement: a picture showing the area.
-
Dan's of Central Florida, Inc. on Aug 10, 2011Hi there, Repairing just a ragged edge with concrete is going to be a tough job. You might be able to get a saw with a cement cutting blade and slightly angle the cut so as to chop off the broken bits and make it a smooth edge. How far are you going with the new tile (you mentioned redoing the tile)? Just on that one section or more? How badly is it chipped? Can we get a close up photo of the damaged sections?Helpful Reply
-
-
Woodbridge Environmental Tiptophouse.com on Aug 10, 2011You are best served to remove the damaged cement section and replace it with new. By the photo it looks as though there was some reaction from the cement slab to the tile that was installed. Although not an expert in this area I would think that perhaps water has seeped under the stone facing and caused the cement surface to spall due to salts released in the cement when they come into contact with moisture. Any patching would eventually fail in any case. With the amount of work it takes to get the job done right its sometimes better to go that little extra mile and make it last.Helpful Reply
-
-
Itsreally C on Aug 10, 2011its not difficult IF its your specialty but, for the avg diy'er, its not easy. 1st, you need specialty materials; 2nd, diamond blade & grinder, 3rd, knowledge & experience. patch the spalls w/white cement concrete dusted w/some coloring agent & quit hitting the adjoining slabs w/your hammer - that's why they make brick chisels ;-)Helpful Reply
-
-
Yung W on Aug 10, 2011I though one can have a close up of the picture I attached. if Not I will take a closeup of the edge and forward it to you as needed. Edge is about an inch deep defining a 3'x5' area or a hole, and the edge is irregularly broken off !!! So we need to trim off to made a clean edge for tile job.Helpful Reply
-
-
KMS Woodworks on Aug 11, 2011Yung...You wouldn't happen to be a software engineer per chance? The layout of the removed tiles are screaming "order and precision" Is this in a finished garage? it looks like an epoxy coated floor in the foreground. One option that is somewhat DIY friendly would be to add tile to the face of the "riser" Then tile over this new edge. Using a cement based thinset will provide a "concrete" like surface. It look to me like maybe the old install used a latex mastic that was somewhat compromised. The adhesive or mastic residue on the stoop will need to be ground off, smoothed or removed before new tile can go down.Helpful Reply
-
Related Discussions
How do I fix a cracked polyethylene planter?
I dropped an empty planter (not terra cotta) and it has a thin crack. I need an easy way to fix it so I can use it. If there isn't an easy way, how could I upcycle i... See more
Can you make your own rain gutters?
I'm interested in creating homemade rain gutters for the second-floor balcony of my house, and I'd love to learn from your knowledge. Can you please share your DIY ra... See more
How do keep the plastic on solar lights from clouding over?
i have solar lights in my yard and i'm wondering how i can keep the sun from clouding the "glass" covers? the lights look so pretty!!! thnx!!!
How can I refresh an old ugly lampshade?
How can I refresh an old cloth lamp shade that has just gotten stained & ugly over the years. The shade is a strange shape so I need an easy solution. Any ideas? Than... See more