I have another project to tackle, I have a kitchen floor shown in the pics, I want to replace this floor with ceramic
-
JL Spring & Associates on Sep 26, 2011Looks like it was a sort of glue down Kenneth(but not too good of one!) When the time comes, I'd move the appliances out of the way and start pulling the vinyl floor up...I'd start at that weekened corner and use easy and steady pressure. If you find that it isn't coming up easy, then the original adhesive is doing it's job and you should be able to go right over it with ceramic tile, just make sure the floor is clean and is solid enough where the grout won't flex and crack. Best to you, thanks for the pix, much easier to advise! JLHelpful Reply
-
-
3po3 on Sep 26, 2011I recommend pulling up all that vinyl flooring. Worth the effort in the long run, and it shouldn't be too hard. You might have some ugly adhesive residue, but you can find adhesive removers at any hardware store.Helpful Reply
-
-
JL Spring & Associates on Sep 26, 2011This citrus solvent works on a lot of those adhesives and smells good too!Helpful Reply
-
-
KMS Woodworks on Sep 27, 2011This could go either way...I know of many jobs were people will lay backer board over this and just tile away. The backer is set with adhesive and nailed or screwed in place. It is the cheaper and faster version of pulling it up. I have done it a couple of times that way at the insistance of the HO on a tight budget. Normally I whip out my trusty 6" wide bladed floor scrapper and have at it. Getting the vinyl up allows you to inspect the subfloor for damage or rot...which ALWAYS should be fixed before any long term tile project. If the sub-floor fails in 5 years due to old issues...the tile will also fail. From your pic it looks like some type of repair was done in front of the door...do you know the details about that?Helpful Reply
-
-
Metro Flooring & Design on Sep 28, 2011Use 1/4 perma base before you lay your tile. I couldn't tell from the pictures if your subfloor was particle board of plywood. If particle board, you should replace it with a good grade of CDX plywood, then install your concrete board and tile. DO NOT TAKE SHORT CUTS ON THIS ONE OR YOU WILL BE WASTING YOUR MONEY. Improperly installed tile on a wood subfloor will crack.Helpful Reply
-
-
Nichter's Home Services Corp on Sep 28, 2011Yes, peel it up. Pop that quarter round off at the basebd too. Oh, and get rid of the dog that dug this vinyl up. Second, pull that door and reset it over a membrane to protect the exterior subfloor or it will be rotting before you finish this job. Third if you have a particle bd underlayment, replace it with a second ply of plywood glued and screwed to give you a decent substrate. Then lay Ditra as a decoupling tile base, following the directions as to which thinset to use.Helpful Reply
-
-
Imagery on Oct 01, 2011Pull it if you want it done right. Start fresh, no hiding the old...there are likely hidden issues anyway. It's worth your effortHelpful Reply
-
-
Ji.flooring2009 on Oct 01, 2011You should pull the old vinyl and replace the osb with cdx plywood 5/8 or better depending on the substrate beneath. Then if using Hardi-Backer Board1/4" or 1/2" you should lay Liquid nails on the non grid side of it then it should always be screwed down with the BackerBoard designed screws and NOT nailed. The reason you dont nail this product onto a floor is because when setting tile you want to have as little movement as possible. If you nail it there is really nothing to stop the nail from backing out hence squeaking floors. Screws are the way to go it grabs, pulls, and stays in spot. Liquid nails or (construction adhesives) are used as an extra precaution only but not nessessity. back to nails and movement, if any movement occures the grouting will be the first thing to crack and break out then loose tiles and or broken tiles jsut get it done the right way first so you wont have to deal with the headache laterHelpful Reply
-
-
JL Spring & Associates on Oct 01, 2011PJ is on the mark with this and don't forget to countersink the screws enough where you can spackle the screw holes so those indentations won't show through the new vinyl should you go that way. If replacing with tile or hardwoods, the indentations are a non-issue! Best of luck and show some project pix....JLHelpful Reply
-
-
HandyANDY - Handyman & All Repairs, LLC on Oct 01, 2011Right on PJ - all good advise given...if you've never done this kind of work...again..best left to pro's. Never nail subfloor or backerboard...just asking for problem....even though the websites say nailing is ok. From your pic....you're best to get it all out and start from scratch. Problem with overlaying in our area....you can create a mold trap between the old floor and the new floor. Good luck!Helpful Reply
-
-
Moda Floors and Interiors on Oct 24, 2011Yes, pull up that vinyl and make sure you are on level plywood before you lay cement board underlayment!! A perfect tile install is the result of making sure the substrates beneath are done correctly so as not to compromise the integrity of the tile on top!Helpful Reply
-
-
Sheila D on Apr 07, 2014Been there..We used a Heat gun made to remove vinyl tile. Time consuming but worth it in the long run. Otherwise have to put a liner and primer down to retile. Besides, you never know what you might find and like underneath. Let us know how it goes.Helpful Reply
-
-
Irish53 on Jul 19, 2014Time to pull it up and start from scratch. Is there hardwood flooring underneath or just subflooring? If you have a wood floor you going to need to put a barrier down to protect it. I would spend the time to give yourself a totally clean floor to lay your tile on. Before you lay the tile down I would think of where the worn spots are now. Are you going to change the placement of table so the traffic through the kitchen is different? If not, do you need to think of how to protect the tile surface.Helpful Reply
-
Related Discussions
I have a light color grout in my ceramic floor in my kitchen and I can
Which room would you pick for a room makeover in your home?
We're curious, if you could redesign any room in your home, which is the room you would choose?Whether it's your cozy living room, your bustling kitchen, or even your... See more
How do I stop the pitting on my stainless steel refrigerator?
I have a 7 month old Frigidaire brand stainless steel refrigerator and I noticed pitting and rust spots numbering somewhere around 30 or 40. Is there something I can... See more
How do I replace rotting trellis?
I have trellis separating my garden, it has climbers growing through it. The trellis has started to rot and one post has snapped. What would you replace it with? I li... See more
I had soaked my gas stove top in bleach overnight.it has turned black
please advise on how to cleanThank you
Why are ants coming from under my toilet & around the toilet base?
There are these black ants coming from under my toilet and I don't know why. Food sources? Stagnant water? Bathroom flooring issues? I find these tiny ants in the toi... See more